Question: a student has chosen the particular weight of 1.373 kg for gear and optimised is by getting the following plot. Taking into consideration these points. A) comment on the plot? B) why high contact stiffness ratio is important and high mesh as well? Contact stiffness 23.0 21.0 19.0 90 17.0 57 72 67 62 15.0 28 $2 $2931 2325 3032 26 27 18 21 Normal module [mm] 4.600 82 2.862 63 1.125 13.0 1.000 1.100 1.200 1.300 1.400 1.500 1.600 1.700 Total contact ratio

Question: a student has chosen the particular weight of 1.373 kg for gear and optimised is by getting the following plot. Taking into consideration these points. A) comment on the plot? B) why high contact stiffness ratio is important and high mesh as well? Contact stiffness 23.0 21.0 19.0 90 17.0 57 72 67 62 15.0 28 $2 $2931 2325 3032 26 27 18 21 Normal module [mm] 4.600 82 2.862 63 1.125 13.0 1.000 1.100 1.200 1.300 1.400 1.500 1.600 1.700 Total contact ratio

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.2P: 5.2 Evaluate the Prandtl number from the following data: , .

See similar textbooks

Similar questions

using the sine bar technique, find the value of the angle for the given data: the stacked height was composed of the following values, 30, 20, 5, 2 and 1.1 mm. The length of the sine bar is 150 mm. Support your answer by sketch.
Match the terms precision and accuracy to their definitions. Precision 2 Accuracy Match each of the options above to the Items below. The number of significant digits or the closeness of different measurements of the same quantity to each other. The closeness of the measured or calculated value to the true value 1 2
No Go holes and H7/p6 tolerances
Problem 3: Insulation To=1 Toowwww Steam Tx2 T₂ T3 www www R₁ R₁ R₂ www.T R₂ Steam at T1 = 320 °C flows in a cast iron pipe (k= 80 W/m. °C) whose inner and outer diameters are 5 cm = 0.05 m and D₂ = 5.5 cm = 0.055 m, respectively. The pipe is covered with 3-cm-thick glass wool insulation with k = 0.05 W/m. °C. Heat is lost to surroundings at T2 = 5 °C by natural convection and radiation, with a combined heat transfer coefficient of h₂ = 18 W/m². °C. Taking the heat transfer coefficient inside the pipe to be h₁ = 60 W/m². °C, determine the temperature drops across the pipe and the insulation. The determination is based on a unit length of the pipe (L = 1 m). Assumptions 1. Heat transfer is one-dimensional since there is no indication of any change with time. 2. Heat transfer is one-dimensional since there is thermal symmetry about the centreline and no variation in the axial direction. 3. Thermal conductivities are constant. 4. The thermal contact resistant at the interface is…
please read everything properly... Take 3 4 5 hrs but solve full accurate drawing on bond paper don't use chat gpt etc okk.... Not old solutions just new solve
The following information is available for Edgar Corporation’s Material X. Annual Usage 12,600 units Working days per year 360 days Normal lead time 20 days The units of Material X are required evenly throughout the year. What is the reorder points? Assuming that occasionally, the company experiences delay in the delivery of Material X, such that the lead time reaches a maximum of 30 days, how many units of safety stocks should the company maintain and what is the reorder point? Show computation.
True, False or Uncertain. Explain your answer. Own wage elasticity JELLlincrease if product demand elasticity n? is high. In short run, when there is an increase in wage rate, each firm will hire less labor and so the industry labor demand is simply the horizontal summation of firm's labor demand. а. b. Labor demand is represented by the marginal revenue produce schedule (MRP) when we have competitive product market while it will be represented by the value of marginal product schedule (VMP) when we have a product market monopolist. When elasticity of substitution, SLK, increase that means the L and K are less substitutable, and the isoquant will be L-shaped. Minimum wage imposed by the government is always bad for the economy because it increase unemployment and deadweight loss. с. d. e. 3.
production planning and control help please
A new electronic component for aircraft is tested to withstand temperatures as low as -50°F. One engineer suggests that the device cannot actually stand temperatures that low. What are the Type I and Type II errors? Type I: The device CAN NOT withstand temperatures as low as -50F but the engineer incorrectly finds that it CAN.Type II: The device CAN withstand temperatures as low as -50F but the engineer incorrectly finds that it CAN NOT. Type I: The device CAN withstand temperatures as low as -50F but the engineer incorrectly finds that it CAN NOT.Type II: The device CAN NOT withstand temperatures as low as -50F but the engineer incorrectly finds that it CAN. Is the answer the first or second bullet point?
Rods are mass produced by a machine. The specification required the length of each rod to be between 42.49 cm and 42.51 cm. The machine produces rods whose lengths are normally distributed with standard deviation 0.005 cm. a) b) Determine the percentage of rods produced which would be rejected if the machine is set so that the mean length of the rods is 42.501 cm. c) Determine the mean length the machine must be set so that only 3 rods in 1,000 will be of length less than 42.494 cm. If there is a need to reduce the total percentage of rejects (oversize and undersize) what should be the mean setting of the machine? You are required to show the normal distribution curve to determine the answer for Part (a) and (b).
Problem # 5 During the manufacture of hard disks, the height between the disk and the head, the headlift, must be controlled. One manufacturer recorded 0.239 0.246 0.245 0.243 0.239 0.241 0.248 0.246 0.243 0.242 0.251 0.246 Find the a) Sample mean b) Sample standard deviation c) Coefficient of variation
Tire manufacturers recommend that you check your tire pressure monthly to avoid unnecessary tire wear and enhance safety. This is best done when the tires are cold meaning; the car has not been driven for at least 2 hours. Since you leave for work before the sun comes up you decide to inflate your tires to the recommended pressure right after you get home from work in the afternoon when the tires are still warm. What would you find if you rechecked your tire pressure after the tires have cooled down? A.Tire pressure has decreased because there is a decrease in kinetic energy of themolecules resulting in more collisions with the inside walls of the tire thusincreasing the pressure inside the tire. B.Tire pressure has increased because there is a decrease in kinetic energy of the molecules resulting in fewer collisions with the inside walls of the tire thus decreasing the pressure inside the tire. C.Tire pressure has increased because there is an increase in kinetic energy of the…