Pravinbhai 1.1 Le poteau ABC a une section transversale rectangulaireuniforme avec b = 12 mm et d = 22 mm. Le poteau est bloquédans le plan xz en son milieu C et supporte une charge centréeP = 3,8 kN. Sachant qu'un facteur de sécurité de 2,0 est requis,déterminez la plus grande longueur L autorisée. Utilisez E =200 GPa.Notes: - Utilisez la formule d'Euler pour déterminer la capacitédu poteau;- Le poteau est articulé aux deux extrémités dans lesdeux directions.1.2 Déterminez la longueur maximale L permise du poteaud'acier pour respecter les exigences de résistance aux étatslimites de la norme S16 si P₁ = αP, σy = 350 MPa, α = 1.5.

The objective of the question is to determine the maximum length of a post that can support a given…

Answered: 1.1 Le poteau ABC a une section…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Pls help ASAP
1. What are the properties of natural gas? 2. Outline the difference between non associate and associated gas i need clear ans and solve very very fast in 20 min and thank you | DYBALA
ANSWERCD
I need , RAy and RBy with complete solution write it on a paper. Thank you for helping.
Please do this carefully.
Calculate the rate of flow of waste thermal energy out of the engine in the exhaust gases in kW (to 1 decimal point). If the air inlet temperature is 35 °C, the air to fuel ratio is 10:1, the inlet air mass flow rate is 37 kg/hr, the specific heat capacity of exhaust gas is 1.13 kJ/kg/K, and the exhaust temperature is 500 °C. Add your answer Integer, decimal or E notation allowed
F P F- b 30 mm 50 30 mm mm Solution workout of this question with proper FBD has to be submitted in MS Teams. Please note down (screenshot) this question. A cutter is about to cut a cable with its jaws parallel as shown. The dimension b=0.071 m, and the applied force at the handles is F=17.4 N. Choose from the options below (a) the force on the cable, and (b) the force in the member PQ.
An electric hot water heater consumes 3.1 kilowatts of electricity and converts it to heat. How long will it take the water heater to heat a 67 gallon tank of water from 10 degrees Celsius to 50 degrees Celsius? (1 kilogram of water is 0.37 gallons, 1 Calorie = 4200 J). It may be helpful to refer back to the weekly handout for guidance on this problem. Your final answer should be in minutes (rounded to the nearest 10 minutes).
As per NPCP, a shower compartment or bath shall have a minimum interior area of 0.6 sqm and it shall be capable of encompassing a 762 mm diameter circle. What shall be the least possible length in millimeters of the shower compartment assuming it is rectangular in shape? (round off your answer to the nearest hundredth and write your answer in this format : 000.00 mm)
1. Nitrogen contained in a piston-cylinder device is compressed from 0.5 to 0.2 m³. During the process, the pressure and volume are related by PV2=aV+ b. The values of a and b are given in the table below. Calculate the work done on the nitrogen during this process. (25 Points) Student number 1 210505269 a (kPa.m³) 8.0 b (kPa.m6) 4.0
Tire manufacturers recommend that you check your tire pressure monthly to avoid unnecessary tire wear and enhance safety. This is best done when the tires are cold meaning; the car has not been driven for at least 2 hours. Since you leave for work before the sun comes up you decide to inflate your tires to the recommended pressure right after you get home from work in the afternoon when the tires are still warm. What would you find if you rechecked your tire pressure after the tires have cooled down? A.Tire pressure has decreased because there is a decrease in kinetic energy of themolecules resulting in more collisions with the inside walls of the tire thusincreasing the pressure inside the tire. B.Tire pressure has increased because there is a decrease in kinetic energy of the molecules resulting in fewer collisions with the inside walls of the tire thus decreasing the pressure inside the tire. C.Tire pressure has increased because there is an increase in kinetic energy of the…
Given the table of results find the following. Give answers in KW. Please show all working out Rate of heat transfer to evaporator from the chilled water Rate of heat transfer from condenser to the cooling water Rate of heat transfer to refrigerant in Evaporator using enthalpy values Rate of heat transfer from refrigerant in Condenser using enthalpy values Work input from the compressor to the refrigerant using enthalpy values

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS