5. Determine the value of the distributed load w and the concentrated loads x, y and z in the load diagram. [x=5.75kN, y=15kN, w= 5kN/m, z=34.25kN] 80 kN-m 5.75 X V (kN) 50N A 5m V (N) M (Nm) B 5 -9.25 6. Determine the value of A, B in the shear force diagram and C in the bending moment diagram. [A =50N; B = -50N; C = 125Nm] 10N/m 10m -5m- C W Z -.x(m) -34.25 50N -x (m) B -x (m)

Q: If the horizontal displacements of nodes 2 and 3 of the following element are q2=0.2 mm and q3=-0.1…

A: Given: Here are the given data, q2=0.2 mmq3=-0.1 mm To find: The horizontal displacement of point…

Q: For the truss in figure below, the cross-sectional area of the truss members is A = 500 mm² and…

A: For the truss in figure below, the cross-sectional area of the truss members is A = 500 mm²…

Q: Find the reactions by drawing a free body diagram and then draw the shear force diagram. 30 kN 50 kN…

A:

Q: 3. For the two-bar structure shown below, determine the global stiffness matrix K and the force…

A: Formulating the elements based on the case you are solving is the initial step in solving any FEA…

Q: Suppose that the following rod system is subjected to a specific amount of load that makes the…

A: Given the displacement of node 2 and 3.  Required: Stress at node 1.

Q: Determine the displacements and forces on each node shown below. The units of force and displacement…

A: here given data is,  K1=200 lb/m K2= 400 lb/m K3= 100 lb/m K4= 300 lb/m Now we will make element…

Q: Find the torque created by the 2 forces about the origin. Ignore the 15 kNm load. (It is called a…

A:

Q: E, A E, 2A E, A 1 L 2 L 3 404/2 L 4 a) Find the displacement at node 2, 3 and 4 b) Calculate the…

A: Given:To find:(a) Nodal displacements.(b) Stress in each element.

Q: After an unfortunate accident occurred at a local warehouse, you were contracted to determine the…

A:

Q: A person is pulling a weight as shown below. His shoulder joint is not moving, but his elbow joint…

A:

Q: Please can you help with the free body diagram for this problem

A:

Q: For the picture below, choose the correct free body diagram. 15m AN 800N 600N Im Im A Fac Nono A 2m…

A: Introduction Free-body diagrams are used to depict the magnitude and direction of all forces…

Q: 25*10^6 psi, and for element 3, A = 3 in^2 and E = 10*10^6 psi.  There is a Force applied to the…

A:

Q: The composite shaft, consisting of aluminum, copper, and steel sections, is subjected to the loading…

A:

Q: W A L A Test beam Strain gauge (a) Unsymmetrical cantilever beam with weight applied at the free end…

A: The objective of the question is to calculate the location of the centroid, the second moments and…

Q: 4. The section of peripheral nerve in neck is under tension of force F=0.18N due to sudden movement…

A:

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.