A uniform 4 lb rod is supported by a pin at O and a spring at B and is connected to a damper at A. Determine (a) the differential equation of motion for small oscillations, (b) the angle the rod will make with the horizontal 5 s after end B has been pushed 0.9 pulg. down and released. c = 0.5 lb. s/pie k = 15 lb/pie A 12 -L/2- L/2. B

A uniform 4 lb rod is supported by a pin at O and a spring at B and is connected to a damper at A. Determine (a) the differential equation of motion for small oscillations, (b) the angle the rod will make with the horizontal 5 s after end B has been pushed 0.9 pulg. down and released. c = 0.5 lb. s/pie k = 15 lb/pie A 12 -L/2- L/2. B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Solve a,b,c and for c when the two dampers are connected to rigid bar (not parallel or series)
+ b 3. A tuning fork is an example of a "resonant system", that is, one that has a low damping ratio. A model of a (half) tuning fork is rod of mass m with air drag modeled as a damper connected approximately at its middle, and a torsional spring at the base of the cantilever. Assume the cantilever rotates back and forth about its pivot by a small angle o. Because other forces are much larger, you can reasonably neglect the effect of gravity in this model. The moment of inertia of a cantilevered beam pinned at one end is equal to ml2, where I is its length. (a) What is the natural frequency of this system if m= 0.1 kg and k = 2548 Nm/rad, and 1 = 0.1 m. Please give the value in rad/s and Hz. (b) Find an upper bound on the damping coefficient b that insures that the damping ratio of the tuning fork is no greater than = 0.01. (c) For this damping ratio, what is the damped natural frequency of the system? (d) For this damping ratio, what is the decay rate (the size of the exponent…
7. Which of the following changes does not affect the period of a horizontal mass-spring system undergoing simple harmonic motion? a. doubling the mass b. attaching an identical spring in parallel (as seen in the figure) c. attaching an identical spring in series (as seen in the figure) d. the presence of friction between the block and the horizontal surface e. Any change which does not affect the ratio of maximum amplitude to maximum velocity
Problem 8: A spring hangs vertically from a bracket at its unweighted equilibrium length, as shown in the left-most image. An object with mass mm is attached to the lower end of the spring, and it is gently lowered until the spring reaches its new equilibrium length, as shown in the center figure. Referring to the right-most figure, the mass is raised until the spring returns to its original length, and then it is released from rest resulting in vertical oscillations. Part (a) If the spring constant is 7.5 N/m, and the mass of the object is 0.25 kg, find the oscillation amplitude, in meters. Part (b) Find the maximum velocity, in meters per second, of the oscillating mass.
5. After a mass weighing 10 pounds is attached to a 5-foot spring,the spring measures 7 feet.This mass is removed and replaced with another mass that weighs 8pounds. The entire system isplaced in a medium that offers a damping force that is numerically equal to the instantaneousvelocity.a. Find the equation of motion if the mass is initially released from a point 1/2 foot belowthe equilibrium position with a downward velocity of 1 ft/s.b. Express the equation of motion in the form x(t) = Ae sin[( )t ]
A mass weighing 1.96N stretches a spring 0.98m. The mass was compressed to 0.5m and released with zero initial velocity. A damping force of 3.6N when the velocity is 3 m/s. a. Determine the equation of motion. b. Plot the motion. At what time will the mass be at maximum displacement from equilibrium? What is the position of the mass at this instance?
A weight of 32 pounds is suspended from a spring with a modulus of 5 lb/ft. From equilibrium position, the weight is pulled down 4 inches below and then released. Given that the damping force in pounds is numerically equal to four times the instantaneous velocity, what is the position of the weight after sec.
Question (4-1): A machine of mass 940 kg produces a vertical disturbing force which oscillates sinusoidally, having amplitude of 320 N at the machine's normal running speed of 550 rev/min. At this speed the force transmitted to the floor is to have amplitude of not more than 100 N, and to achieve this the machine is to be mounted on viscously damped springs. The static deflection of the spring mountings is to be not more than 15 mm, and the amplitude of vibration at resonance is to be kept as low as possible. Find (a) the total spring stiffness and total viscous damping coefficient which will enable these conditions to be satisfied, and (b) the resonance speed of the machine when such mountings are fitted. Ans: 615kN/m, 8850 N.s/m,25.1 rad/s.
1- A shaft carrying a rotor of weight 100 lb has an eccentricity of 0.1 in rotates at 1200 rpm. Determine, a- The steady state whirl amplitude b- The maximum whirl amplitude during start up condition of the system. The shaft stiffness is 200000 lb/in and the external damping ratio is 0.1 2- A single-story building frame is subjected to a harmonic ground acceleration, as shown in Fig. Find the steady-state motion of the floor (mass m). (1) = A cos cof
Solve the Following Problem: Critically Damped Vibrations View Image. PS. Show complete solution Write eligible
A mass weighing 8 pounds is attached to a spring whose constant is 4 lb/ft. The medium offers a damping force that is numerically equal to the two times instantaneous velocity. The mass is initially released from a point 1 foot above the equilibrium position with a downward velocity of 8 ft/s. (a) Specify the 2nd order DE as an IVP for the mass spring system.
2. The stiffness of a close coiled helical spring is such that it deflects 36 mm when an axial load of 10N is applied on the end hook. Calculate (i) the mass to be hung on the spring so that when set vibrating it will make one complete oscillation per second. The mass of the spring is 0.6 kg. Calculate also the maximum velocity and the maximum acceleration of the vibrating mass when initially displaced 12 mm from equilibrium.