Dimension the holes & shafts for the required linear tolerance. Also calculate the hole tolerance, shaft tolerance, maximum clearance, & allowance DIAMETER: 2.00 INCHES A) TYPE OF FIT: RC 3 C) DIAMETER: 10 mm TYPE OF FIT: H9/09 Hole Tol: Shaft Tol: Max. Clearance: Allowance: Hole Tol: Shaft Tol: Max. Clearance: Allowance: Hole Tol: Shaft Tol: Max. Clearance: Allowance: Hole Tol: Shaft Tol: Max. Clearance: Allowance: B) DIAMETER: 1.00 INCHES TYPE OF FIT: LT2 DIAMETER: 12 mm D) TYPE OF FIT: H7/h6

Q: Pin: MMC LMC Geom. Tol. с 1.000 1 1.000 Ø.515-.540 Hole 0.010M ABC 1.000 B Figure for Problem 21…

A:

Q: a) Calculate the Pitch diameter for the following thread. Given the measurement over the wires is…

A:

Q: . a. On the part shown, show a angularity specification to orient the angled surface in relation to…

A:

Q: I have three parts that I need answered pertaining to the print provided below.   Did the person…

A: Yes, the given print is created by using the cylinder rule. Hence, the option (a) is correct.

Q: FIND THE CUBIC SPLINE G(x) for the given data k0 and kn as given 12. fo=f(0) = 1, ₁ = f(2)=9,…

A:

Q: what is the MMC of shaft dimension 1.375 /- .030?

A: Given: The dimension of shaft  is 1375/-0.30 MMC :MMC stand for  Maximum Material Condition.

Q: Q- In a limit System, the following limits are Specified for hole and shaft. calculate the tolerance…

A: The limits of the hole are..The limits of the shaft are..

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: Suppose parts are to be fitted together as shown below. Dimensions and tolerances (in inches) are in…

A: Given: The dimension with tolerances are d=1.750±0.003, a=0.150±0.006, c=1.400±0.001. The dimension…

Q: I need help with question number 15 that is pertaining to the print provided.

A: 15.The unidirectional system is used here for the dimension placing. The unidirectional system is…

Q: Apply the necessary symbology to establish the required tolerance and datum features to control the…

A:

Q: 3. If the tolerance applies at MMC then a possible O indeterminant bonus O LMC zero tolerance…

A: given = fill in the blanks

Q: For the following part sizes and geometric tolerances, determine the appropriate geometric tolerance…

A: A.    Geometric tolerance = 0.005 + 0.007                                     = 0.007…

Q: Complete the needed calculations and enter the needed values in the given table. All problems are…

A:

Q: 8. If the limits of size for a hole are .384" and .394" diameter, and the position tolerance is…

A: Write the given data. Minimum limit=0.384"Maximum limit=0.394"Positional tolerance at MMC=0.009"

Q: ead intrustions on example and help anwser it please and th

A: Jsolid Cylinder =πd432 DAC = 0.9 JAC =π 0.9432=0.064412467

Q: Given the drawing below, the table shows the range of possible produced sizes and 4 optional feature…

A:

Q: or a floating fastener application, a hole size specification of 385" minimum and .395" maximum…

A: Given  For hole     Maximum diameter = 0.395 in    Minimum diameter = 0.385 in Find   Final minimum…

Q: If the pin in the drawing below is produced at Ø.498, what is its total positional tolerance? C…

A: Given data as per the question Pin diameter =0.498

Q: Three blocks A, B, and C and a grooved block D have dimensions a, b, c, and d as follows: a =…

A:

Q: Consider the figure shown below, (enter all answers in this format 0.XXX) 4XØ 255 a 005 O 010 B -50…

A: TOTAL POSITION TOLERANCE The GD&T symbol for location tolerance is position tolerance. The True…