: Determine the required head H at the inlet section of the oil pipeline. The piston speed is V=15 cm/sec? Take into account the losses along the length. Given: =1,8 m, d=10 mm, D=60 mm, P=500 N, ta=30°C, steel pipes. Oil is I-12. ado amnne H

: Determine the required head H at the inlet section of the oil pipeline. The piston speed is V=15 cm/sec? Take into account the losses along the length. Given: =1,8 m, d=10 mm, D=60 mm, P=500 N, ta=30°C, steel pipes. Oil is I-12. ado amnne H

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: a pipe system is as shown er a total head of 100 ft at 40°F. Atmospheric press PSH is 9 ft, will…

A: data we have discharge = 495gpm total head = 100 ft tempertaure = 40°F Atmospheric pressure…

Q: A pipe of diameter 400 mm carries water at a velocity of 20 m/s.The pressure ta point A is 300000…

A: To find : The loss of head between A and B . Given data : The diameter of pipe is (D)=400 mm. The…

Q: Reservoirs A, B and C are located atop a hill as shown. Use the formula for headloss: hf = 0.083fsQ?…

Q: 10.0 m A 200m 2. An old western town has a water tower to deliver water to the residents. Pictured…

A: Note: Since you have asked multiple question, we will solve the first question for you. If you want…

Q: Q5: For the system shown in figure. Find the total head loss from (A) to (B). the pipe…

Q: The diameters D & d piped, Venturi- meter like horizontal water flow sistem seen in the drawing is…

Q: Q2/A Kaplan turbine develops 1500 kw under ahead of 6 m. the turbine is set 2.5 m race while the…

A: Given data as per questionPower develop by Kalpan turbine, P=1500 kWHead, H=6 mDraft tube has…

Q: Ex:- 200 L/see water flow in Verrtical PiPe, The tiameter for The small pipe (75 mm) expandeA by…

Q: A pipe reduces it size from 300mm diameter at point 1, to 100mm diameter at point 2. The pressure at…

Q: In Figure below, the pipe entrance is sharp-edged having K1 = 0.5, and for the open globe valve…

A: Given that, K1=0.5K2=6Flow rate of water, Q=0.015 m3/sec,Density of water, ρ=1000 kg/m3Friction…

Q: -. Calculate h, (loss head) in a pipe through the water is flowing...

A: V=3 m/sd=250mm=0.250ml=100 mk=0.4ζ=6ρ=100 kg/m3ν=1*10-6 m2/s

Q: Elevation = ? reservoir on the right at a rate of 0.45 m/s. The formula for the head losses in the…

Q: Q4: The two chambers in the skaned are combined with asbestos cement pipes, Eind the flow rates…

A: From the above diagram-

Q: 3) What are the flow Q and the velocity V when total head loss is H = 25 m? KENTRANCE = 1.0 KGLOBE…

Q: 6 m^3/min of 15.6°C SAE 30 is to be pumped from a tank through 40 meters of horizontal pipe; the oil…

A: Given:Volumetric flow rate of oil, Q=6 m3/min=660m3/s=0.1 m3/sOil temperature, T=15.6oCLength of the…

Q: The following system is fed by a centrifugal pump. The piping is constructed from smooth plastic of…

Q: Water flows from the reservoir on the left to the - Elevation ? reservoir on the right at a rate of…

Q: A series of commercial steel pipe which length, I = 20 in. and diameter, d = 0.8 in. is placed on…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: he figure shows a siphon discharging oil (sp.gr.= 0.90). The siphon is composed of 75 mm pipe…

Q: Problem : Taking into account only the local resistances, determine the level difference in the tank…

Q: :Determine the absolute pressure at the inlet section of the pump. Flow rate of the pump Q=2,3…

Q: Q3/ The pipe has a different diameter: diameter (Di = 4 m) changes into (Dz = 6 m). The water…

Q: Saturated water at 310K is being pumped from a tank to an elevated tank at the rate of 7L/s. All of…

A: Given-Data:- To-Find:- Power (W)=?

Q: 3. Problem: What head H must be created at the beginning of the oil line in order to ensure the…

Q: Plate 30m V, Rx= Given z Rx = 890 Y %3D water

A: Given that, Rx=890 N,head of water, h=30 m,θ=90°ηt=90 % v=2ghv=2×9.81×30v=24.261 m/sec The…

Q: What is the maximum height the higher reservoir can sit and be filled using a fixed-speed pump with…

A: Pump Power, P=114HP=1+0.25=1.25HP=687.50lb.ft/s Pump Efficiency, η=57% Volumetric flow rate,…

Q: dia Y lo psi Q=10,000 gpm flow oil (sy=086b) I 14"' dia Determine the horizontal force on the…

Q: fluid sulphuric acid with 75% concentation is to be pumped for 0.8 km along a 50mm density 1650…

Q: water is being delivered at a rate of 2000 gpm for a reservoir to a subdivison below resvoir…

A: RESERVOIR A repository is most generally an augmented regular or fake lake made utilizing a dam to…

Q: 3. In the figure shown, find the head lost from the inlet to the throat. Water Mercury S-13.6

Q: Water is pumped between two reservoirs in a pipeline with the following characteristics; (d=275mm,…

Q: 7. A siphon draws oil (sg=0.86) as shown in the figure. Determine the volume flow rate of oil from…

A: Consider 1 is the section in the siphon at the level of oil in the tank, and 2 is the section at…

Q: A horizontal pipe carries cooling water at 10°C for a thermal power plant. what is the pressure in…

A: Given data: The average velocity in the pipe can be determined as,

Q: :-in the figure shown find the pump power if the discharge of oil is 200L/sec and the relative…

Q: For the branching pipe system given below, determine the flow to and the elevation of the third…

A: The friction factor for all the pipes is .The flow from reservoir to junction is .The flow from…

Q: R=d насос

A: NOTE:- Here, for 90 degree bend, connection type is not give so I take it threaded connection…

Q: Calculate the power supplied to the pump shown if its efficiency is 75%. Water is at 25 degrees…

Q: A pump delivers water from a tank (A)X water surface elevation=D110m) to tank B (water surface…

Q: The piping system shown in the figure is to move ethylene glycol at a flow rate of 50 gpm. Follow…

A: Requirement Pump Head =Friction Pressure drop + losses due to fittings and Valves +Gravity head…

Q: Problems: two vessels are connected by a pipe of the diameter of d=100 mm and length of =12 m, made…

Q: 3. Water is pumped through three pipes in series. Compute the discharge if the power delivered to…

Q: 6.5 BELLOWS 8100mm The horizontal elbow is joined by bellows to the rest of the piping system and it…

A: NOTE: According to Bartleyby's policy we shall answer only one question at a time so kindly repost…

Q: The properties of the air in the inlet section with A1 = 0.25ab m2 in a converging-diverging channel…

A: Write the given information.

Q: The flow rate of the system is 1 cubic meter per second. Determine the major and minor losses of the…

A: The flow rate of the system, Q=1 m3/s=35.3147 ft3/s 1…

Q: In the pipeline in the figure, water is transmitted from a-tank to Bdepo with a flow rate of 400L/s…

A: Water flow rate, Q=400 L/s=0.4 m3/s Pipe lengths, L1=20 m, L2=30 m Pipe diameters, D1=0.2m, D2=0.4 m…

Q: 3. The water tank of a city is going to be drained for contamination purposes, calculate the maximum…

Q: A pipeline has the following data at its two section A and B Item Section - A Section - B Diameter…

A: water flowing through point B to A at point B, D2 =0.45m, Z2 =16m, P2 =30KPa, α2 =1.25 at point A,…

Q: determine total head loss of the system and gauge pressure p2 in order to deliver water at 2…

A: For solution refer below images.

Concept explainers

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.

Question

. Problem: Detemine the required head H at the inlet section of the oil
pipeline. The piston speed is V=15 cm/sec? Take into account
the losses along the length. Given: =1,8 m, d=10 mm, D=60
mm, P=500 N, toäl=30°C, steel pipes. Oil is I-12.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

2. A turbine is used to produce 2700 hp by expanding the water between points 1 and 2. Water flow rate, static pressures and pipe diameters are given. Calculate the power lost in between point one and two. Note that the static pressure at point 2 is given in vacuum. (SGH =13.6) P1 = 60 psi Q = 150 ft³/s D = 3 ft Section (1) Turbine 10 ft P2 10-in. Hg %3D vacuum D2 = 4 ft Section (2)
1) Determine the Pressure and Velocity head at each point. Find the exiting flowrate. Point 1 2 3 4 5 6 Kent=1 Pressure Head Pipe 1 Kbend-0.2 Kexp=0.3 Velocity Head Kval=2.2 Elevation Head 70 62 50 48 45 43 4 Kbend-0.2 Kcont=0.1 Pipe 1 2 3 4 5 6 Kexit=1 Lm 250 150 150 170 100 200 D mm 150 150 300 300 300 150 f 0.022 0.022 0.02 0.02 0.02 0.022
The turbine at C draws a power P kW. If the intake B has a diameter of de mm. The pressure dg(mm) dĄ(mm) at the intake B is Ps kPa and the velocity of the water (density = 1kg/L) at that point is v (m/s). The frictional losses between A and B are At neglected, and the exit A has a diameter of da B1 mm. Consider the data in the table to M = last two digits of your student ID P (kW) = 0.5M + 68.5 da(mm) = M + 150 dp (mm) %3D М + 400 PB (kPa) = M + 380 v (m/s) = 0.1M + 4 a- Calculate the velocity at the exit A b- Calculate the discharge at the exit A c- Calculate the turbine head d- Calculate the pressure at A m=13
L Elowregimes. Rids mumber 2 Non positivai technical parameters and characteristics 3. Problem:Determine the head H of water in the tank. Given: flow rate ps e principle ofoperation, 1,d Q=71/s, d=30 mm, l=3 m, =30°. Par
Ex2-The two pumps (n=1800 rpm) each have the following characteristics: h= (100, 90, 80, 60, 40, 2O)ft and Q=(0, 110, 180, 250, 300, 340)gpm, are to be used in parallel. They must develop a head h = 35 + 20Q2 What is the flow rate with both pumps operating at 1800 rpm? Ans: 170 gpm
Explain the major and minor losses? Then solve for the parallel pipes system shown below, a pump is placed in line 2 so that 0.142 m³/s will flow through each pipe. Pipe material is cast iron and for each elbow. Find the relation between the head loses hL1 and h12 and estimate the necessary pump head. Water viscosity is μ=1x10-³ Pa.s. Line 1, L-30 m, D= 6 inches Q₁-0.142 m³/s Pump Line 2, L, 30 m, D-3 inches Q-0.142 m/s R
Ex ....... HYDRAUE • The pump is to be connected to a rising main which has a diameter (D) of 400 mm and a length of 137 m.The entry exit and minor head losses in the pipeline can be taken as 80D in this particular situation. The friction loss can be approximated by h; = ALQ² / 1 2D5 with A=0.04. The static lift is 10 m. By considering a single pump (P). And two of the pumps in series (P+P) and parallel (P//P) determine: > the H-Q curve of the two pump combinations » Which combination will be capable of discharging at least 0.3 m³/s, with the ability to pump up to 0.35 m³/s if the need arises. %3D
A pumping system has the following characteristics, f=0.015 length of thepipe = (2500 ft) pipe diameter 6 in, losses less than 0.5, the pipeis cast iron, and the system curve is:Hp= 34+ 5.47Q2Knowing that the system curve and the pump curve intersect at 12 cfsa. Determine Operation headb. Determine dischargec. Plot the system curve
In the figure below, assume the pipe from B to C has a diameter of 4-inches, (f = 0.035), and length of 18-feet. The pipe from DE is 187-feet, has a diameter of 4-inches and friction factor of 0.035. The Az = 69-feet. The elevation of C is 14-feet above the lower water surface. If the pressure head @ C is to be no less than (-) 20 feet, and the pump has 63% efficiency, what horsepower must be supplied to the pump in order to convey flow through the system? (Kent = 0.8) Assume a submerged exit. Az
A pumping system has the following characteristics, f=0.015 length of the pipe = (2500 ft) pipe diameter 6 in, losses less than 0.5, the pipe is cast iron, and the system curve is: Hp= 34+ 5.47Q2 Knowing that the system curve and the pump curve intersect at 12 cfs a. Determine Operation head b. Determine discharge c. Plot the system curve
QUESTION 6 Pump BC in figure delivers 8 cfs through the pipe system shown. The elevation at reservoir D has to be maintained at 77 ft. There is a valve in the discharge pipe with a loss coefficient of 5. Neglect other minor losses. EL 20.0 37 20 78 20-18 f-0.030 400-12" EL. 10.0-0.020 The head (ft) developed by the pump is: 57 K=5.0
A centrifugal pump having a head-capacityrelationship given by the equation ha=180 –6.10 X 10-4 Q2, with ha in feet when Q is ingpm, is to be used with the system shownin the figure, For Z2-Z1= 50 ft, what is theexpected flowrate if the total length ofconstant diameter pipe is 600 ft and thefluid is water? Assume the pipe diameter tobe 4 inch and the friction factor to be equalto 0.02. Neglect all minor losses.