Pleas explain in details.The suction side of a pipe system is as shown in the figure. The pump discharges 495gpm of water under a total head of 100 ft at 40°F. Atmospheric pressure = 32.7 ft of water.If the required NPSH is 9 ft, will there be a cavitation problem? Please note that 1 cfsequals 449 gpm.Diameter = 10 inL = 300 ftSteel12 ft6 ft

data we have discharge = 495gpm total head = 100 ft tempertaure = 40°F Atmospheric pressure…

Answered: a pipe system is as shown er a total…

a pipe system is as shown er a total head of 100 ft at 40°F. Atmospheric press PSH is 9 ft, will there be a cavitation problem? E

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Not yet answere Question 7 Marked out of 1 In ideal case and knowing that the area of the Venturi at…

A: Given :- In ideal case and knowing that the area of the Venturi at the inlet and outlet is the…

Q: Problans: or 20 cn During Go Cm vonturi has a throat dianeter a o min test it discharged S10 cu…

A: Dear student as per the policy i can answer only one question , request you to post the remaining…

Q: A container is filled with a liquid of density p. The surface of the liquid is at atmo- spheric…

A: The expression is obtained using Bernoulli's principle.

Q: Q5) A pump of 20 kW power is discharge oil to the over tank as shown in fig. (5). If the efficiency…

Q: If you measured h=880.5 mm Hg using simple manometer, then the pressure (in kpa) will be:(Given:…

Q: A 4 m high tank is filled with diesel. If the nozzle of the bubbler system is located 3 meters below…

Q: In the Figure.Q3, The energy decline of the connections and the pipe before the pump is 3m.…

Q: A liquid of (u = 1.25 Pa.s.) fills the space of (Sum) shown in figure below. Calculate the forque…

Q: 1. In the benzene plant, the pressure drop at some point of a pipeline in which benzene is passing…

A: Given: The height of water in left column, hw,left = 4 cm The height of water in right column,…

Q: Q6: A: Explain the cavitation in pumps then list its signs and problems. 1

A: This question is based on the concept of cavitation in fluid mechanics.

Q: B EL? Q3: Answer ONE Section only. a. Three reservoirs are connected, if pipe (1) and pipe (3)…

Q: Liquid of sp.gr and u is in a closed tank with air at pressure measured by a manometer of R reading.…

Q: P- 60 psi Q - 150 ts D; = 3 ft Section (1) Turbine Pz = 10-in. Hg vacuum D2= 4 f1 Section (2) Figure…

Q: A 32 m high down Comer-tank system operates lloo bar if the exit quality of the steam is what will…

A: Given Volume, V = 32 m3 Initial pressure, P1 = 100 bar Quality, x = 0.5…

Q: 1. A bubble (assuming perfectly spherical) was released from a depth of 120m in the body of water by…

A: (a) Write the expression of absolute pressure when bubble is released. Pabs=Patm+ρgh1

Q: -Example the values. asystem total head. against. for the initial condition, show below - give the…

Q: Air at 200°F flows through a pipe with 0.5 inch diameter at a rate of 0.08 Ibm/s. What is the flow…

A: The temperature of the air is T=200°F. The diameter of pipe is D=0.5 in. The flow rate of the air is…

Q: Caleulate the pressute difference letireen the two pipes A and B.

A: Given, The specific gravity of oil = 0.75

Q: At a flow rate of 10 LPM, what will gonna happen if the pressure drops over 90 seconds from 0.657…

A: The flow rate given asthe time taken, pressure drop, the given pressure,

Q: (a) State the cquation of contmity for a compressible tluid flowng thouglh a pipe.

A: Continuity equation: It states that" the rate mass of mass entering at any cross-section of a pipe…

Q: 3- Discuss the siphon process and what benefit of it?

Q: Q2: Two pipes A and B carrying water are conected by a connecting tube as shown in Figure. If the…

Q: Findthe pressure at a depth of 15 m below the free surface of water in a reservoir.

Q: deilling fluid or drilling mud density 863 26/9allan. dePth- to00 ft + ConVert reading to Water…

A: Given Density = 8.63 lb / gallon Find Density interns of lb / ft3, psi / ft, and SG

Q: For transferring of water, a pump is installed in the height of 3 m above the surface of the water.…

A: hsp=Pρg=100kpa1000×9.81=10.19hs=3mhf=4mhvp=Pvρg=10kpa1000×9.81=1.019

Q: A water flows through a pipe at a certain velocity of the pressure gauge reading is 2 bar. The datum…

Q: Assuming a permanent loss using the pressure drop from the 180 L/min flow rate and taking energy to…

A: Flow rate ,Q = 180 L/min or 0.003 m3/s Time = 24 hours

Q: b) An inverted differential manometer is connected to two pipes A and B The fluid in the manometer…

Q: Typical solution

A: Step 1:

Q: Industrial Application of differential U tube manometer?

Q: e static pressure diff al section through wil flow rate, the mercu

Q: Liquid of sp.gr and u is in a closed tank with air at pressure measured by a manometer of R eading.…

Q: Calculate the pressure reading if L = 1.5 m, ?and the angle= 10 , liquid S.G =0.8

Q: A 300 mm x 150 mm venturimeter is inserted in a vertical pipe carrying water flowing in upward…

Q: WATEVS @ 50°C , Flow From a tank , Throngh 75 cm. Galvanizto Inon ( G.I) pipE the dis charge low oe…

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

Pleas explain in details.
The suction side of a pipe system is as shown in the figure. The pump discharges 495
gpm of water under a total head of 100 ft at 40°F. Atmospheric pressure = 32.7 ft of water.
If the required NPSH is 9 ft, will there be a cavitation problem? Please note that 1 cfs
equals 449 gpm.
Diameter = 10 in
L = 300 ft
Steel
12 ft
6 ft

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A fan can develop a static pressure head of 350 mm water gage through standard air condition. What is the new static pressure head if fan will operate at 95⁰C and 720 mm of Hg?
The density of water is looe ty/m? and the e Plective bwlk modulus (klis 1.06 Gpa. in a 5omLony pipe Carries water at 1.86 nls. that calculate DP in Mpa. AP=pv pelton wheel the velocity of ) In the incident jet relative to the bucket the water jet velocity is is 6.28 m Is, 23.54 m/s and volumetric flov rate f the jet 109 m/s. Tn an ideal itnation (Cy, * and cos© are all eqnal to !) m/s. In an ideak 2it wat ion Hint V= V, -U = V, -wR DV = (V, -U) (1+k coso) mee W = 27N 60 raA /s
95kPa AIR hc he n A hA An Air tank is connect to a U-tube that contains three separate liquids as follows: (A) mercury, (B) kerosene (C) brine ha = 50 cm hB = 40 cm hc= 30 cm If the atmospheric pressure is 95 kPa, find the pressure in the Air tank.
Which of the ff are statements made in construction the Bernoulli eq? that the velocity at the inlet is negligible that the pressure at the inlet and outlet must be atmospheric that the flow through the orifice is in the laminar regime that the inlet and outlet are on the same level horizontally
dy E. A Venturimeter having inlet diameter 1.8 cm and throat diameter 0.5 cm. The oil-mercury differential manometer has a reading of 5 cm. Calculate the discharge of an oil of SG=0.9.
3. In the figure below, ax = 12.88 ft/s? and ay = 0. Find the imaginary free liquid surface and the pressure at B, C, D and E. Ans. B = 0.347psi, C = 0.069psi, D= 1.109 psi, E = 0.693 psi ay B 1ft A+ 3ft ax OIL - Sp. Gr. 0.8 E 3ft 4. With the same figure as Problem 3, if ax = 8.05 ft/s? and ay = 16.1 ft/s?, find the imaginary free liquid surface and the pressure at B, C, D and E. %3D Ans. B = 0.347psi, C = 0.069psi,
For the parallel-pipe system of Fig. each pipe iscast iron, and the pressure drop p1 - p2 = 3 lbf/in2. Computethe total flow rate between 1 and 2 if the fluid is SAE10 oil at 20°C.
I will give rating for correct answer.