Answered: Determine the magnitude of the pin…

Determine the magnitude of the pin force at A. Assume W = 795 lb, a = 3.9 ft, b = 2.8 ft, r = 7 in. W Answer: A = i a B A D lb b

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter8: Engineering Materials

Section: Chapter Questions

Problem 85CQ

See similar textbooks

Related questions

Q: Determine the magnitude of the pin force a Assume W = 895 lb, a = 4.8 ft, b = 3.3 ft, r = r W C…

Q: The dimensions a = 2 m and b = 1 m. The couple M = 2400 N.m. The spring constant is k = 6000 N/m,…

Q: Given the following, determine the reactions for the beams. Please show step by step solutions so I…

A: Step 1: Step 2: Step 3: Step 4:

Q: eter of 40 mm. It is subjected to the force normal stress that acts at point A. answer to three…

Q: 3.Calculate and determine the nature of all forces in the bar using the point balance method 800 N 3…

Q: Set P = 49 kN, P₂ = 37 kN. (Figure 1) Figure P₁ N 2 m 1.5 m ▾ Part A Determine the force in member…

Q: Compute the rectangular components (vertical and horizontal) for the 400-lb force shown below. X(-)…

Q: Consider the frame in (Figure 1). The crate weighs 550 lb. Follow the sign convention. Figure 4 ft…

A: A crate of mass, P = 550lb is applied at D as shown.To determine at EThe shear force The bending…

Q: ume F₁ = 250 lb, F₂2 = 80 lb, and F3 = 120 lb in ure 1). Replace the loading by an equivalent…

A: F1=250lbF2=80lbF3=120lbTo find resultant, it's direction and distance from point A

Q: The two bars are used to support load P. When unloaded, joint B has coordinates (0, 0). After load P…

Q: Problem 1: Determine the force in members FE and EB. State if the members are in tension or…

A: The free body diagram is shown below,

Q: The rod supports a weight of 390 lb and pinned at its end A. It is also subjected to a couple moment…

Q: The 26-mm-diameter A-36 steel rod is subjected to the axial forces shown. Take E = 200 GPa (Figure…

A: A loaded steel rod is given and it has been asked to calculate deflection at ‘C’ which is fixed at…

Q: 2. Determine the resultant fo

Q: A #2 Determine the slope and the displacement at the end C of the beam. E = 200 GPa, I = 70(106)…

A: Given: Required: Slope and deflection at C

Q: Consider the frame in (Figure 1). The crate weighs 550 lb. Follow the sign convention. Figure 4 ft D…

A: Mass of crate = 550 lbTo determineThe normal force at FThe shear force at FThe bending moment at…

Q: Question 1 [Soalan 1] Determine the force in each cord for equilibrium of the x k horizontal due to…

Question

Determine the magnitude of the pin force at A.
Assume W = 795 lb, a = 3.9 ft, b = 2.8 ft, r = 7 in.
r
W
C
Answer: A = i
a
B
A
D
lb
b

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A beam is part of the framing system for the floor of an office building. The floor is subjected to both dead loads and live loads. The maximum moment caused by the service dead load is 45 ft-kips, and the maximum moment for the service live load is 63 ft-kips (these moments occur at the same location on the beam and can therefore be combined). a. If load and resistance factor design is used, determine the maximum factored bending moment (required moment strength). What is the controlling AISC load combination? b. What is the required nominal moment strength for a resistance factor of 0.90? c. If allowable strength design is used, determine the required moment strength. What is the controlling AISC lead combination? d. What is the required nominal moment strength for a safety factor of 1.67?
Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.
Verify the value of Zx for a W1850 that is tabulated in the dimensions and properties tables in Part 1 of the Manual.
Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine the increase in vertical stress at point A located z = 15 ft below the surface. Given: x = 27 ft. Figure P6.4
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A column in a building is subjected to the following load effects: 9 kips compression from dead load 5 kips compression from roof live load 6 kips compression from snow 7 kips compression from 3 inches of rain accumulated on the roof 8 kips compression from wind a. If lead and resistance factor design is used, determine the factored load (required strength) to be used in the design of the column. Which AISC load combination controls? b. What is the required design strength of the Column? c. What is the required nominal strength of the column for a resistance factor of 0.90? d. If allowable strength design is used, determine the required load capacity (required strength) to be used in the design of the column. Which AISC load combination controls? e. What is the required nominal strength of the column for a safety factor of 1.67?
A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
Determine the smallest value of yield stress Fy, for which a W-, M-, or S-shape from Part 1 of the Manual will become slender. To which shapes does this value apply? What conclusion can you draw from your answer?
Compute the nominal shear strength of an M1211.8 of A572 Grade 65 steel.
Use an elastic analysis and determine the maximum load in the weld (in kips per inch of length).
A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?