Determine the indentation diameter and the surface area of indentation of a copper material subjected to a Brinell hardness test with a test force of 7.1 kN using a hardened steel ball indentor of 9 mm. Take the Brinell Hardness Number as 955. Solution: i) Indentation Diameter (in mm) = 3.0314043041657 ii) Surface Area of Indentation (in mm?) = 7.434554973822

Determine the indentation diameter and the surface area of indentation of a copper material subjected to a Brinell hardness test with a test force of 7.1 kN using a hardened steel ball indentor of 9 mm. Take the Brinell Hardness Number as 955. Solution: i) Indentation Diameter (in mm) = 3.0314043041657 ii) Surface Area of Indentation (in mm?) = 7.434554973822

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider a metal rod with a critical resolved shear stress of 40 MPa for a specific crystallographic plane (hkl). The angle between the normal to the plane and the applied force is 30 degrees, and the angle between the slip direction and the force is 15 degrees. Two force levels of F1 = 75 N and F2 = 40 N is applied. The cross-sectional area of the rod is 1 mm^(2). Will the slip initiate at the two force levels? Select one: a. F1: Yes, F2: No b. F1: No, F2: No OC. F1: Yes, F2: Yes Od. F1: No, F2: Yes
An aircraft component is fabricated from an aluminum alloy that has a plane strain fracture toughness of 31 MPa/m. It has been determined that fracture results at a stress of 227 MPa when the maximum (or critical) internal crack length is 2.47 mm. a) Determine the value of Yo√a for this same component and alloy at a stress level of 340 MPa when the maximum internal crack length is 1.24 mm. i MPa √//m b) Under these circumstances will the component fail? No Yes Unable to Determine 3
Annealed low-carbon steel has a flow curve with strength coefficient = 80,000 lb/in2 and strain-hardening exponent = 0.25. A tensile test specimen with gage length = 2.0 in is stretched to a length = 3.5 in. Determine the flow stress and average flow stress that the metal experienced during this deformation. use correct stratgy and correct E 0.55962
Determine the indentation diameter and the surface area of indentation of a copper material subjected to a Brinell hardness test with a test force of 7.3 kN using a hardened steel ball indentor of 11 mm. Take the Brinell Hardness Number as 948. Solution: i) Indentation Diameter (in mm) = ii) Surface Area of Indentation (in mm2) =
Determine the force applied to a hardness specimen that has Brinell hardness number as 974 and the surface area of indentation as 15 mm2. The force applied to the Hardness Specimen (kN)=
Q1. (i) Initial strain Please enter your supplied question data Q1. (ii) Eo B (hr¹Pa-¹) n IVICUITO Fracture 0.003 Please enter your answers here Your Q1. (i) Answers: 4.60E-34 Q1. (ii) 3.2 Q2. o (Pa) σo (Pa) 780,000,000 Q3. t (hr) Q2. A component is made from a metal that is known to be viscoelastic and behaves according to a secondary creep rate equation with constants of B and n provided as your input values. If the component is subjected to a constant force that results in the initial strain of E provided to you, determine the design stress for a secondary creep life of 1,000 hrs before attaining a limiting strain, &, of 0.01. Q3. If the same component is subjected to a constant displacement that results in the value of initial stress, o, provided to you, calculate the time for the stress to reduce to 200MPa. Young's modulus of the bolt is E = 200GPa.
Determine the initial length of a tensile specimen that has a percentage of elongation as 43 % and the final length at fracture 67 mm.
Stress Strain Diagram The Data shown in the table have been obtained from a tensile test conducted on a high-strength steel. The test specimen had a diameter of 0.505 inch and a gage length of 2.00 inch. Using software. plot the Stress-Strain Diagram for this steel and determine its: A= TTdT(050s A %3D 1. Proportional Limit, 2. Modulus of Elasticity, 3. Yield Strength (SY) at 0.2% Offset, 4. Ultimate Strength (Su), 5. Percent Elongation in 2.00 inch, 6. Percent Reduction in Area, 7. Present the results (for Steps 1-6) in a highly organized table. e Altac ie sheet (as problelle 4 A = 0.2.002 BEOINNING of the effort Elongation (in) Elongation (In) Load Load #: #3 (Ib) (Ib) 1 0.0170 15 12,300 0.0004 1,500 16 12,200 0.0200 0.0010 3. 3,100 17 12,000 0.0275 0.0016 4,700 18 13,000 0.0335 5. 6,300 0.0022 19 15,000 0.0400 0.0026 6. 8,000 20 16,200 0.055 0.0032 9,500 21 17,500 0.0680 0.0035 8. 11,000 22 18,800 0.1080 0.0041 11,800 23 19,600 0.1515 0.0051 24 20,100 0.2010 10 12,300 0.0071 25…
small crack, 4mm deep, is found on the edge of a large, thick plate structure. The plate is continuously subjected to a uniform cyclic tensile stress (in the direction perpendicular to the crack plane) which varies from 0 MPa to 100 MPa and back to 0 MPa every 40 seconds. If the next inspection is to take place in 30 days, would it be safe to delay the replacement or repair of the plate until that time? The stress intensity factor, KI, for this type of crack is related to the nominal stress, G, and the crack length, a, via the relationship is K, = 1.12a Va %3D For the plate material, the yield stress is 800 MPa, the fracture toughness is 50 MN/m2 and threshold stress intensity factor range is 6 MN/m3/2, The fatigue-crack growth rate per cycle for the material, da/dN, can be defined by: 3/2 da / dN = 2.8 x 10-12 (AK,) ^PY (m/cycle) Where AK1 has unit MN/m e 8:34 /
A mild steel material is subjected to a Brinell hardness test with an applied force of 7830 N using a hardened steel ball indentor of 10 mm and it is found that the Brinell Hardness Number as 936. Determine the surface area of indentation and indentation diameter. i) Surface Area of Indentation (in mm2) ii) Indentation Diameter (in mm) · --
The data shown in the table below were obtained from a tensile test of high-strength steel. The test specimen had a diameter of 13mm and a gage length of 50mm. At fracture, the elongation between the gage marks was 3.0mm and the minimum diameter was 10.7mm. Plot the conventional stress-strain curve for the steel and determine the propotional limit, modulus of elasticity (i.e the slope of the initial part of the stress-strain curve), yield stress at 0.1% offset, ultimate stress, percent elongation in 50mm, and percent reduction area. TENSILE-TEST DATA Load(kN) Elongation(mm) 5 0.005 10 0.015 30 0.048 50 0.084 60 0.099 64.5 0.109 67.0 0.119 68.0 0.137 69.0 0.160 70.0 0.229 72.0 0.259 76.0 0.330 84.0 0.584 92.0 0.853 100.0 1.288 112.0 2.814 113.0 Fracture
An engineer determines that a 32 cm long rod of 1020 grade steel will be subjected to a tension of 40 kN. The following two design requirements must be met: the stress must remain below 120 MPa, and the rod must stretch less than 0.135 mm. Determine an appropriate value for the rod's diameter to meet these two requirements. (Round up to the nearest millimeter when reporting your answer.) mm