Determine the greatest A punch press has the cast steel frame shown in Figure force P that can be exerted at the jaws of the punch without exceeding a stress of 18 ksi at section A-B. The properties of the area are as shown and 1-1 is the centroidal axis. 20" PY Figure Д -8"-12" Section A-B 11-1 = 4000 in.4 Area = 120 in.²

Determine the greatest A punch press has the cast steel frame shown in Figure force P that can be exerted at the jaws of the punch without exceeding a stress of 18 ksi at section A-B. The properties of the area are as shown and 1-1 is the centroidal axis. 20" PY Figure Д -8"-12" Section A-B 11-1 = 4000 in.4 Area = 120 in.²

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A force E= 52 N is applied to a two-bar truss as shown and 0 = 43 degree. Determine the value of F1, in newton. Type answer in two (2) decimal places only without the unit. FBD F 30°
2. Determine the normal stress in members BD, AC, and BC in the truss shown. The cross- sectional area of each member is 1500 mm2. Indicate whether the stresses are tensile (T) or compressive (C). Use 2 decimal places in every solved value. 10 m 10 m 10 m K 6 т H 6 т 15° 15° 50 kN 40 kN E F 6 т C D б т A B
6.59 A square section as shown in the figure below is subjected to bending moment M. (c) Obc = Obl y || h y H What is the maximum bending stress? (a) Obc = obt 12M h³ 9M 2h³ JXC h (b) bc = Obt = (d) %bc =%bt = 6M 4³ 9M h³
The rigid bar ABCD of negligible weight is initially horizontal, and the steel rods attached at A and C are stress-free. Ifa20-kip load is applied, determine the vertical displacement in the barat ?and C that will cause a stress in the rod at C to be 50ksi. Indicate the direction of movement. Use E=29x106psi for steel.(Provide FBD and movement diagramin your computation).
Situation 2: The bar AB is being supported by bars at each end. The length and the area for each bar are given. Determine the distance x to where the 100 N load must be applied if the bars must have the same stress. A. Distance x (feet) L-3 ft A= 0.2 in L=2 ft A= 0.3 in 100 N B. 8 ft
Sispose that P = 30 kip, P=20 kip, and = 10 kip Figure ++. 400 San 184-399 30 Part A Determine the force in member GF of the bridge truss Express your answer in kilopounds to three significant figures. Enter negative value in the case of compression and positive value in the case of tension For Submit Part B Avec Fre Request Anst O? Determine the force in member PC of the bridge truss Express your answer in kilopounds to three significant figures. Enter negative value in the case of compression and positive value in the case of tension VAZO IT vec kip ? kip
DETERMINE FORCE (N) OF MEMBER EG in the truss shown. F1 = 214 N %D F2 = 876 N %3D F3 = 435 N a = 38 degree X = 15 m. **Note: for compression, include a negative sign (- ) and for tension, type your answer as is. Input your answer in two (2) decimal places only without the unit. В H A C E G F1 F2 F3
Assume that the truss is simply supported at joints M and E. Determine the stress at member DE if Pu = 18.375 Kips, the area is 23 in?. Answer your problem with the given unit ksi. Pu Pu Pu Pu Pu Pu Pu * (a: 10' - J I H G K F * (a ' - RI Rv 8@10'=80
Problem 04.107 - Maximum load carrying capacity of a milled rod with known allowable stress A milling operation was used to remove a portion of a solid bar of square cross section. Knowing that a = 30 mm, d = 20 mm, and all = 54 MPa, determine the magnitude P of the largest force that can be safely applied at the centers of the ends of the bar. The magnitude P of the largest force that can be safely applied at the centers of the of the bar is KN.
A steel rectangular block is subjected to a uniform stress of o = 150 MPa acting on all faces. The dimensions of the block are as follows: L_x=100 mm,L_y=30 mm,L_z=40 mm. Determine the change in length along the y-axis. Use E = 200 GPa and v 0.3. Note that ɛ_0=-o/E(1+2v). A -0.03 mm -0.015 mm -0.009 mm -0.012 mm
Load P is applied to joint D and the temperature increases by 50 °F. There are two steel (E = 29*10^6 psi; a = 6.5*10^-6/°F) AD and DC and a bronze (E = 16*10^6 psi; a = 9*10^-6/°F) BD with a length of 50 inches. Each bar is a 0.75 inch diameter. Find the deformation of every rod, the displacement at D, and the stress in each rod.
02) The cantilever beam is subjected to the load shown Below. Determine 1. the actual stresses acting at point A. (Hint: Tmax = 1936x(0.5). 2. IfG =30 GPa find the angle of twist at the free end of beam. Y 10 kN 25 NA 120 mm 15 500 mm Good Luck and be Green