The bar AB is supported by two rods- steel on the left and bronze on the right. If the bar is horizontal before load P is applied, find the distance x (in meters) that locates the position where P must act if the bar is to remain horizontal. (E of steel 29000 ksi and E of bronze = 83 GPa) Neglect the weight of bar AB. L=2ft Aw02 in? A 0.4 in 1on

The bar AB is supported by two rods- steel on the left and bronze on the right. If the bar is horizontal before load P is applied, find the distance x (in meters) that locates the position where P must act if the bar is to remain horizontal. (E of steel 29000 ksi and E of bronze = 83 GPa) Neglect the weight of bar AB. L=2ft Aw02 in? A 0.4 in 1on

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Help with fbd ,20-30mins
P (kN)=80 L (m)=0.65 A1 (mm2)=540 A2 (mm2)= 650 Eal (GPa)=74 Est (GPa)=205
Q.1//The bar AD is considered to be absolutely rigid and is horizontal before the load of 200 KN is applied. The connection at A is a pin, and AB is supported on the steel rod BE and the copper rod CF. The length of BE & CF is 250 mm. The cross sectional area of CF is 400 mm', the area of BE is 200 mm. Determine the stress in each of the vertical rods . The weights of all bars are negligible. For copper E=120 GPa, for steel E=200 GPa. 200 KN B. 1.5 m 500 mm 11500 mm 250 mm steel сорper
In this part, you should base your calculations upon a material of your choice. You have to assume areasonable factor of safety.B.1 Determine the maximum force P that can be supported at joint D .B.2 calculate the cross-sectional area of each member to safely carry the axial load.
A bar AB is attached at A as fixed support. A small spaces can be seen on the other side of the bar prior to another rigid surface. Load P is applied on the bar located at two-thirds of length L from point A. Determine the small space s if the support reactions at A and B are to be equal due to the external load P. See all necessary parameters below. L A E P A 3 m 2500 mm² GPa 45 77 KN 2/3 -L 113 mm -L ANSWERS: ALL ANSWERS SHOULD BE IN THREE (3) DECIMAL PLACES INCLUDING ZEROS 01 (delta due to external load P) = 52 (delta due to Reaction at B) = Small Space s = mm S₁ mm B
Determine the force in the member CE of the truss shown. It has F1=13 and F2-3 loaded as shown. Answer in two decimal places. Numerical values only. Don't indicate units here, just on the submitted solution. 2.53 m 2.07 m, -5.4 m F2 F1 2.25 m E F 4 m 3 m B)
250 mm A D P = 25 kN B 30 60 C TOP VIEW 280 mm Member AD is fabricated by joining two bars (E0=205GP,, Ga=82GPA) and is pinned to plate ABC using a 5 mm diameter pins as shown in the figure. The yield strength of the pins is T,=890MPA. Plate ABC is a right triangle and is fixed along its edge BC. A 25KN Force P is then applied at end D causing a lateral strain in member AD with magnitude equal to 7.5x10-mm/mm. This also causes Point A to displace only along the horizontal resulting to a shear strain at point A equal to y,=+0.00165rad. Determine the following: 1. Poisson's ratio of material used in member AD, vAD 2. The normal strain in member AD, caD 3. The average stress experienced by pin A, T, 4. Factor of Safety of pin A with respect to yielding, FS,A 5. Displacement of point D, A,
Compute the total deformation (in mm) of the tapered square steel bar caused by the 30-kN axial load. Use E = 200 MPa. 20 mm 30 mm 30 kN 30 kN 400 mm
PLEASE SOLVE THIS ONE AS SOON AS POSSIBLE AND SURELY I WILL RATE YOU.THANK YOU ( STEP BY STEP PROCESS)
The horizontal bar ABC is supported by a pin at A and two rods with identical cross-sectional areas. The rod at B is steel and the rod at C is aluminum. Neglecting the weight of the bar, determine the force in each rod when the force P = 10 kips is applied. Use Est = 29 x 106 psi and Ebr = 12 x 106 psi. %D Steel Bronze A В C e-3 ft - 2.5 ft 1.5 ft VP
Question #4: Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. For the loading shown and knowing that Es = 200 GPa and Eb = 105 GPa, determine (dsteeF 40 mm, dbrass = 30 mm) 1- The reactions at A and E. 2- The deflection at C. 180 B 120 * 60kN 100 100 40 RN D Steel Brass Dimensions in mm.
For the exact in the figure tensile strength = 8000 N/cm^2 compression safety = 3000 N/cm^ 2 calculate the largest Mx moment that the section can carry. S-2) 2.5 3 как 2.S cm pomk CM AA 3.5 3.5 3 CM x<- vy 18cm 15 Cm 5cm