Design experiments in UV-Vis to figure the optimal mole ratio of copper (1:1, 2:1, 3:1 and etc)versus ethambutol using all necessary chemicals including dihydrochloride and copper nitrate hemipentahydrate and sodium hydroxide. Show how UV-Vis absorbance and maximum wavelength would change in response

Design experiments in UV-Vis to figure the optimal mole ratio of copper (1:1, 2:1, 3:1 and etc)versus ethambutol using all necessary chemicals including dihydrochloride and copper nitrate hemipentahydrate and sodium hydroxide. Show how UV-Vis absorbance and maximum wavelength would change in response

Principles of Modern Chemistry

8th Edition

ISBN:9781305079113

Author:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Publisher:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Chapter20: Molecular Spectroscopy And Photochemistry

Section: Chapter Questions

Problem 6P

See similar textbooks

Similar questions

A calibration curve is made for the absorbance as a function of concentration of blue dye (in mg/L). The slope of the curve is 0.131; the y-intercept is -0.01869; the correlation is 0.993. If a consumer sample has an absorbance of 0.120 on the same instrument, what is its concentration of blue dye, in mg/L? a. 0.034 b. 0.935 c. 0.993 d. 1.06
B. Quantitative Spectroscopy Prepare two graphs, %T vs. Concentration and Absorbance vs. Concentration, using the data for the cobalt standards. The concentrations of Cobalt standards 2-4 can be calculated using simple dilution calculations. Concentration should be on the x-axis for each of these graphs. The first should clearly show some curvature while the second should be a linear curve. Using the absorbance graph you can determine the concentration of the unknown. Take the absorbance value for the unknown and find that value on the y-axis. Draw a horizontal line from that point on the y-axis to the plotted line. From the point where the horizontal line intersects the plotted line, draw a vertical line straight down to the x-axis. Record the value from the point where you hit the x-axis as the unknown concentration.
Consider the analysis of a sample of iron using atomic absorbance spectroscopy. Which of the following statements are true? Select all that apply. The iron sample is aspirated into the flame, where the solvent evaporates and the iron analyte is atomized. The hollow-cathode lamp for iron emits wavelengths of light unique for iron. A detector measures the amount of light generated by the flame and not absorbed by iron. The iron atoms in the flame absorb some of the light emitted from the hollow-cathode lamp. The flame replaces the cuvet of conventional spectrometers and the flame pathlength is typically 10 cm.
A student prepared a calibration curve by measuring of the absorbance of five standard solutions of a compound at 300 nm. A cuvette with a path length of 5 cm was used . if the slope of the curve was 300 L/mol. the molar absorptivity of the compound is…….. 60 L mol-1cm-1 1500 L mol-1cm-1 0.20 L mol-1cm-1 5.0 L mol-1cm-1
Spectrophotometric Determination of Nitrate in Seawaters Explain the relationship between absorbance and concentration Explain the principle behind a UV-Vis spectrophotometer (key components and how it works) Why must the absorbance in this experiment be read at a wavelength of 543 nm?
0.1040 g of a solid sample containing copper was dissolved by acid and transferred to a 250.00 mL volumetric flask and volume was made up with distilled water. The solution was then diluted by a factor of 20. The final solution was analyzed by atomic absorption spectrophotometry and the concentration was found be 3.109 ppm, What is the weight percentage of copper in the original solid sample? Keep four significant figures in your final answer. Do not try to include the "%" in your answer. e.g. if your final answer is 10.01%, only write 10.01 in the box.
Find information on fluorescent dye Fluo-3: Display its structure Briefly describe its purpose and the mechanism of operation Display its fluorescence spectra Display transmission spectra of commercially available optical filters required for flow cytometry measurements of cells stained with Fluo-3 (see lecture notes on where to look)
A 0.0138 gram sample of brass was dissolved in a approximately 1 ml of nitric acid and then diluted to 250.0 ml using a volumetric flask. The 20% dilution of the unknown gave an average absorbance of 0.3514 at 213.9 nm. A zinc calibration curve is shown below. Calculate the percentage of zinc in the brass sample. Show your work in the space below. Zn Calibration Curve 1.2 y-0.8339x + 0.0452 R 0.99788 08 06 04 04 Concentration (ppm) Absorbance @ 213.9 nm
Describe the basic design difference between a spectrometer for absorption measurements and one for emission studies?
A standard curve of absorbance vs. concentration has a linear trendline of y = 0.56x + 0.987. Use this trendline to calculate the concentration of an unknown sample that has an absorbance of 1.245.
You have been asked to determine which heavy metals, if any are in a sample of sewage sludge. Why is atomic absorption spectroscopy not a good technique for the job and why is ICP- atomic emission spectroscopy a better choice?
The extinction coefficient for FD&C Blue Dye #1 is 138,500 cm-L/mol at 630 nm. A chemist collected the following data at 630 nm. The student also found that the absorbance of an FD&C Blue Dye #1 solution of unknown concentration was 0.205. Use your Vernier Graphical Analysis to generate a standard curve from this data set, and use it to determine the concentration of the unknown solution. (Report your final answer to 3 sig figs) Concentration of Blue Dye (M) Absorbance @ 630 nm 6.35x10-7 1.23x10-6 3.84x10-6 5.68x10-6 0.088 0.160 0.541 0.787