Design a steel bearing plate from A36 steel for a W24 x 55 beam supported by a reinforced concrete wall with f 'c = 21 MPa. The maximum beam reaction is RDL = 134 kN and RLL = 180 kN. The maximum length of end bearing perpendicular to the wall is the full wall thickness of 255 mm. W24 is a 992 steel.

Design a steel bearing plate from A36 steel for a W24 x 55 beam supported by a reinforced concrete wall with f 'c = 21 MPa. The maximum beam reaction is RDL = 134 kN and RLL = 180 kN. The maximum length of end bearing perpendicular to the wall is the full wall thickness of 255 mm. W24 is a 992 steel.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.3P

See similar textbooks

Similar questions

Item 2 Figure 1 A D of 1 -0.5 m- 400 KN B -0.5 m C 0.4 m Part A The assembly consists of two posts AD and CF made of A-36 steel and having a cross-sectional area of 1100 mm², and a 2014-T6 aluminum post BE having a cross-sectional area of 1700 mm². If a central load of 400 kN is applied to the rigid cap, determine the normal stress in each post. There is a small gap of 0.12 mm between the post BE and the rigid member ABC. (Figure 1) Enter your answers, separated by commas. JAD, CF, OBE = Submit O Π| ΑΣΦ ↓↑ My Answers Give Up vec ? MPa Provide Feedback Continue
A steel column is pin connected at the top and bottom which is laterally braced and subjected to transverse loading. It carries an axial load of 800 kN and a 70 kN-m moment. Use ASD. The steel section has the following properties: A = 13000 mm² r = 94 mm Ix = 300 x 106 mm4 Sx = 1200 x 103 mm³ L = 3.6 m Yield stress Fy = 248 MPa Axial compressive stress that would be permitted if axial force alone existed, Fa = 115 MPa Compressive bending stress that would be permitted if bending moment alone existed, Fb = 148 MPa Members subjected to both axial compression and bending stresses shall be proportioned to satisfy the following requirements: Mry + 9 Mex Mey Determine the axial compressive stress if axial load only existed. Pr 8 Mrx + Pe 75.82 MPa 61.54 MPa 33.96 MPa 16.25 MPa Determine the bending stress if bending moment alone existed. 76.25 MPa O58.33 MPa 13.33 MPa ≤ 1.0 16.59 MPa Determine the value of both axial and bending moment interaction value, considering the amplification due to…
AW 12 x 65 column section shown in the figure is pinned at each end and has an additional support in the weak direction at a point 4.1 m from the top. Use X- 4.8 m K 1 for both directions. X+Y Properties of W 12 x 65 A 12323 mm2 - 134.11 mm ry 76.71 mm Fy- 248 MPa Determine the allowable compressive strength (kN).
A square hollow steel strut if thickness 10mm is pin connected to two connector plates of thickness, 12mm. The connector plates are welded to the base plate of thickness, 12mm. The base plate is fastened to te concrete base by 4-16mm diameter anchor bolts. The diameter of the pin is 16mm. Which of the following most nearly gives the shearing stress in the anchor bolts? Choices 150.00 MPa 59.68 MPa 51.69 MPa 119.37 MPa
1. For the Pratt bridge truss and the loading shown below, determine the average normal stress in member BE, knowing that the cross-sectional area of that member is 60 in². NN K 12-12--12--12--| 50 lips 50 kips 50. ips Figure 1 G xfone
A traffic light signal pole is subjected to the weight of each traffic signal 45 lbs and the weight of the road lamp 55 lbs . The weight of lateral arms is included in the signal and lamp weights. The people is fixed and the base and is made of round structural steel section HSS 14.000 x 0.25. The details of the pole section may be obtained form the Manual of American society of steel Construction (AISC Steel Manual). Analyze the principle normal stresses and the maximum shear stresses on elements A and B located at the base in the pole as shown in the sketch below.
A traffic light signal pole is subjected to the weight of each traffic signal 45 lbs and the weight of the road lamp 55 lbs . The weight of lateral arms is included in the signal and lamp weights. The people is fixed and the base and is made of round structural steel section HSS 14.000 x 0.25. The details of the pole section may be obtained form the Manual of American society of steel Construction (AISC Steel Manual). Analyze the principle normal stresses and the maximum shear stresses on elements A and B located at the base in the pole as shown in the sketch below
Bearing P plate Let the allowable stresses in the post be ost=120MPaand oco=6MPA. Compute the maximum safe axial load P that may be applied. The moduli of elasticity are 200 GPafor steel and 14 GPafor a concrete. Each steel bar has cross-sectional area of 900mm2. Steel - Concrete - 300 mm 300 mm
10 mm | | | | 10 mm 50 mm ارت - 50 mm 10 mm 20 kN B 150 mm 910 mm 10 kN D ------- 150 mm Two vertical forces are applied to a am of the cross section sh vn. Determine the maximum tensile and compressive stresses in portion BC of the beam.Show your complete solution and box your answer.
Need right complete solution
Find the max compressive and tensile normal stress of the beam below
Where is/are the location(s) of the maximum transverese shear stress? A simple I-beam is loaded as shown. 20 mm P KN PKN PKN Į Į -C B с D L/4 m L/4 m Midspan at point C Roller at E at the NA Section B at the top fiber Pin A at point C Midspan at point D Roller E at point D L/4 m L/4 m OE 20 mm 20 mm- 250 mm 150 mm 150 mm A