Design a network to maintain a continuous 15 V DC voltage to a machinary having a load impedance of RL=1,5 k2. In order to realize this request, a transformer having a primer voltage 220 V AC and a seconder voltage 30 V AC (220/30 V AC transformer), some silicon diodes, zener diode and some resistors of 200 2 can be considered in design. %D a) Draw the overall network, explain the tasks of each component and overall operation of the network in your design. b) Calculate load current (IL). c) Calculate power dissipated by zener diode (if used in design).

Design a network to maintain a continuous 15 V DC voltage to a machinary having a load impedance of RL=1,5 k2. In order to realize this request, a transformer having a primer voltage 220 V AC and a seconder voltage 30 V AC (220/30 V AC transformer), some silicon diodes, zener diode and some resistors of 200 2 can be considered in design. %D a) Draw the overall network, explain the tasks of each component and overall operation of the network in your design. b) Calculate load current (IL). c) Calculate power dissipated by zener diode (if used in design).

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.28MCQ

See similar textbooks

Similar questions

Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l3l4RTR182kR275kR356kR462kPT3.436WP1P2P3P4
by High Voltage
Design a DC power supply using FWR to perform the following requirements. Find V_dc, V_rms, V-ripple, PIV of the diode. draw the waveform of (V_in, V_out, L_in, I_load, V_diode and I_diode). Input voltage = 25 Transformer turn ratio 0.1 load resistance = 1k ohm Ripple factor = 0.025 Diode type =Si
Explain five (5) applications of the hall effects With the aid of a diagram, explain how a P-N Junction is form. iii. State five (5) application of PN Junction, and explain the property of the PN junction that make those application possible. Explain what carrier mobility is and elaborate on the factors that influence carrier mobility. A 80 V rms is stepped down to 18V rms by a transformer. The output from the transformer is rectified using a half wave rectifier circuit and connected to a 47.5 Ω load resistor. Draw a circuit diagram of this arrangement and the waveform at each stage. Calculate the following about the circuit in Figure 2.1 (If silicon diodes are employed in the rectification); the peak value of the output voltage considering the drop across each diode, the average voltage, iii. The current through the load resistor, The current diode, The frequency of the output signal, Calculate the efficiency of the full wave rectifier expressed in percentage. vii. Sketch…
Topic- basic & const.
Q-3 A Cockcroft-Walton type voltage multiplier has ten stages with capacitances, all equal to 0.1 µF. The supply transformer secondary voltage is 100 kV at a frequency of 60 Hz. If the load current to be supplied is 5 mA, find (a) the percentage ripple, (b) the regulation, and (c) the optimum number of stages for minimum regulation or voltage drop.
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diodeshave? (Use constant voltage drop model for the Silicon diode) D IN4001 OV 10 kN IN4001 DELL
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D1 IN4001 R. V out OV 10 kN D2 IN4001 llle
I need the answer at 20 minute
1 Design a full-wave regulated power supply using 5:1 center-tapped transformer and an 8-V, 2- W zener diode that will provide a constant 8-V to a load varying from 100 ohms to 500 ohms. The input voltage to the transformer is 110 V, 50 Hz.
Please answer the question step by step and please care to explain the question in detailed with your own sentence and explain why you used that formula, calculations etc asap. Thanks in advance.
Please answer it clear and complete solutions. Thank you.