DEN 11'4" x 11'4" GARAGE 13'-4"x24'-0" LIVING ROOM 18'-0" x 15"-4" W/D P. BATH KITCHEN 11'-8"x12'-6" ENTRY 7-4" x 7'-8" 0' 2' 4' 8" Note: Scale is 1/4"-1'-0" when printed on 11"x17" sheet Two Bedroom House 1,464 Square Feet (Not Including Garage) Slight variations may exist BEDROOM #2 12'-0" x 11'-0" MASTER BEDROOM 12'-0" x 15'-4" SPRINGMOOR LIFE CARE RETIREMENT COMMUNITY Springmoor Plan 20

DEN 11'4" x 11'4" GARAGE 13'-4"x24'-0" LIVING ROOM 18'-0" x 15"-4" W/D P. BATH KITCHEN 11'-8"x12'-6" ENTRY 7-4" x 7'-8" 0' 2' 4' 8" Note: Scale is 1/4"-1'-0" when printed on 11"x17" sheet Two Bedroom House 1,464 Square Feet (Not Including Garage) Slight variations may exist BEDROOM #2 12'-0" x 11'-0" MASTER BEDROOM 12'-0" x 15'-4" SPRINGMOOR LIFE CARE RETIREMENT COMMUNITY Springmoor Plan 20

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter3: Job Planning, Benchwork, And Layout

Section3.1: Understanding Drawings

Problem 9RQ: A dimension listed on an engineering drawing is known as the _______ _______.

See similar textbooks

Similar questions

SPECIFY WHERE DIMENSIONS NEED TO BE PLACED FOR THE FOLLOWING PART NOTE: JUST NOTE WHERE DIMENSIONS NEED TO BE PLACED, NO NEED TO PUT THE ACTUAL NUMERICAL VALUES JUST USE LETTERING A, B, C, ETC.
A dimension listed on an engineering drawing is known as the _______ _______.
Attach the solidworks file if possible
What is the worst-case distance between the bottom surface of the slot and the bottom surface of the part in the drawing below? B 4.000-4.020 O 1.475 O 1.450 O 2.950 O 1.500 O 1.030 4.00 0.010MABM 1.000-1.010 2.00 A
a= 15.0 in, b= 7.0 in, c= 12.0 in, and d= 12.0 in.,(e = 3.0 in. horizontal), Draw the kinematic diagram in SolidWorks drawing sheet with size A3 iso and suitable scale. Solve the following questions and upload the SolidWorks file below. e 'a What is the degree of freedom of the mechanism? а. b. 0 С. 1 d. 4 е. 2.
please answer, thank you
The three fuctional gages below can be used to verify the three segment position specification that is shown earlier in this unit. Calculate the pin sizes for these gages to help explain the callout on the drawing. See Product Drawing earlier in this unit (image 2).
On the attached drawing 11A005< what is dimension "G"
Question 3 Make an Isometric Drawing of the support bracket shown in Figure 4. Take the dimension 'H' as 35 mm. As per standard instruction for pictorial views in ENG1100, no dimensioning is required. Orientate the drawing so View A' of Figure 4 is in the direction of the shaded face of the representative isometric view of a cube shown in Figure 3 with the top of the 'View A' orientated towards TOP' as shown in Figure 3. Top Figure 3 140 22 DRILL 96 - 22 22R 16 41 198 40 - 5/ 51- 16- 19R 16 DRILL-3HOLES 51- View A Figure 4: Support Bracket (Source: Boundy AW, Engineering drawing, 8th edn, McGraw Hill, dimensions altered)
Solidworks
Solidworks
I need help with number 9 with the calculations part.