Consider the circuit diagram below, where: v₁(t): = 12 cos (377t) v2(t) = 15 cos (377t) Amplitudes are given in peak values. Use node analysis to determine the voltage at nodes a and b. Express the voltages as sinusoids in the time domain with phase angles measured in radians. You may solve the system of equations using MATLAB or a similar software, but you must include the code you ran as part of your solution. V1(t) ZC1 -132.63j Ω a ww ZL1 11.304j Ω ZR1 2 ΚΩ b HH ZC2 www -132.63j Ω ZR2 1 ΚΩ V2(t)

Consider the circuit diagram below, where: v₁(t): = 12 cos (377t) v2(t) = 15 cos (377t) Amplitudes are given in peak values. Use node analysis to determine the voltage at nodes a and b. Express the voltages as sinusoids in the time domain with phase angles measured in radians. You may solve the system of equations using MATLAB or a similar software, but you must include the code you ran as part of your solution. V1(t) ZC1 -132.63j Ω a ww ZL1 11.304j Ω ZR1 2 ΚΩ b HH ZC2 www -132.63j Ω ZR2 1 ΚΩ V2(t)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.1MCQ: The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax

See similar textbooks

Similar questions

A certain impedance is given by 1012° N. Does the current lead or lag the voltage, and by how many degrees? Fill in the blanks. The current the voltage by
Give a detailed solution. Please need help
A step-down chopper is to be used to supply power from a 600-V overhead wire to the commutator motor on a trolley bus. The motor may be mod- eled as a generated direct voltage in series with a resistance of 0.2 and an inductance of 25 mH. The frequency of the chopper is set at 500 Hz. (a) When the bus is stopped, what should be the ON time of the chopper to provide a motor current of 150 A? (b) What is the maximum possible generated voltage of the motor for which a current of 150 A can be supplied? (c) What is the average value of the supply current for the conditions of (a) and (b)? បទៅនឹងរស់របស (d) If the motor current is to be continuous, what should be its minimum. value?
A stringed instrument generates a complex waveform with the following components: 250 Hz with an amplitude of 5 Pa 500 Hz with an amplitude of 3 Pa What is the fundamental frequency? What other harmonic is represented? What equation would represent this complex waveform? Calculate the amplitude values every 45° (0°, 45°, 90°, etc.). Plot the resulting points on a graph of degrees vs. pressure, and connect them to see the shape of the complex waveform.
A chopper circuit has an inductive load of 2ohm resistance and 10mH inductance. If the source voltage is 20 V and the frequency of the chopper is set to 100Hz and the on-time to 5 ms. Determine the average voltage and current, maximum and minimum load currents.
In the circuit, v₁ and ₂ are AC sources with = 100 rad/s. The phasor diagram shows the phasors of v₁ and v₂. It is not drawn to scale. You may assume the system is in steady state. V3 is a DC source. (a) What is v₂ where I is the period of the waveform ? (b) What is the waveform ia(t)? (c) What is the maximum value of the waveform va(t)? V3 L + V1 1 + + Va V2 V₂ a Im V₁ να Re |V1|: |V2|: alpha: V3: C: L: 2 V 3 V 30 degrees 3 V 10 mF 25 mH
Thanks for answering this question
An electrical circuit with a sinusoidal voltage source, a resistor, and a capacitor all connected in series. The voltage across the capacitor: Select one: a. Leads the current in the capacitor by exactly 90o b. Is in phase with the sinusoidal voltage source c. Is in phase with the voltage across the resistor d. Leads the current in the circuit by 90o e. Lags the current in the circuit by 90o
Given a capacitive load absorbing 5 kW with a power factor of 0.85. The source connected to this load is an AC voltage supply with 120V RMS at a frequency of 50 Hz. Please find; A) Peak current (m) and RMS Current (ms) Values B) Draw peak voltage and current phasors on phasor diagram with everything labelled C) Find the value of an inductor that when connected in parallel will improve the power factor to 0.95.
Please help with the solution.
1. Suppose that MATLAB is used to plot a sinusoidal signal. The following MATLAB code generates the signal and makes the plot. Draw a sketch of the plot that will be done by MATLAB. Determine the amplitude (A), phase ($), and period of the sinusoid and label the period on your plot. dt = 0.001; tt = = .05 dt : .15; Fo = 8; Z sqrt (2) * (1-j); xx = real( Z*exp( 2j*pi*Fo*tt ) ); plot tt, XX ), grid title( 'SECTION of a SINUSOID' ), xlabel('TIME (sec)')
What are coupled waveforms? Are they at either end of the same magnitude?