Consider a steam pipe of length 20 m, inner radius 7 cm, ouler radius n 12 cm, and thermal conductivity 20 Wim K. The inner and outer surfaces of thepipe are maintained at average temperatures of T 160'C and Ta 65'C, respectively. Applying a general relation for the temperahure distribution inside the pipeunder steady conditions, determine the rate of heat loss from the stoam through the pipe.

Answered: Image /qna-images/answer/7b72ef2e-7bbc-4653-83f7-b2fae3f1ca30.jpg

Consider a steam pipe of length 20 m, inner radius 7 cm, outer radius 12 om, and thermal conductivity 20 Wim K. The inner and outer surfaces of the pipe are maintained at average temperatures of T 100'C and Ta 65'C, respectively. Applying a general relation for the temperature distribution inside the pipe under stear the stoam theough he nine

Consider a steam pipe of length 20 m, inner radius 7 cm, outer radius 12 om, and thermal conductivity 20 Wim K. The inner and outer surfaces of the pipe are maintained at average temperatures of T 100'C and Ta 65'C, respectively. Applying a general relation for the temperature distribution inside the pipe under stear the stoam theough he nine

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.29P

See similar textbooks

Similar questions

Determine the rate of heat transfer per meter length to a light oil flowing through a 2.5-cm-ID, 60-cm-long copper tube at a velocity of 0.03 m/s. The oil enters the tube at 16C, and the tube is heated by steam condensing on its outer surface at atmospheric pressure with a heat transfer coefficient of 11.3 kW/m K. The properties of the oil at various temperatures are listed in the following table: Temperature, T(C) 15 30 40 65 100 (kg/m3) 912 912 896 880 864 c(kJ/kgK) 1.80 1.84 1.925 2.0 2.135 k(W/mK) 0.133 0.133 0.131 0.129 0.128 (kg/ms) 0.089 0.0414 0.023 0.00786 0.0033 Pr 1204 573 338 122 55
A mild-steel cylindrical billet 25 cm in diameter is to be raised to a minimum temperature of 760C by passing it through a 6-m long strip-type furnace. If the furnace gases are at 1538C and the overall heat transfer coefficient on the outside of the billet is 68W/m2K, determine the maximum speed at which a continuous billet entering at 204C can travel through the furnace.
1.21 In an experimental set up in a laboratory, a long cylinder with a 5-cm diameter, and an electrical resistance heater inside its entire length is cooled with water flowing crosswise over the cylinder at and a velocity of 0.8 m/s. For these flow conditions, 20 kW/m of power is required to maintain a uniform temperature of at the surface of the cylinder. When water is not available, air at is used with a velocity of 10 m/s to maintain the same surface temperature. However, in this case, the cylinder surface heat dissipation rate is reduced to 400 W/m. Calculate the convection heat transfer coefficients for both water and air, and comment on the reason for the differences in the values.
7.43 Liquid sodium is to be heated from 500 K to 600 K by passing it at a flow rate of 5.0 kg/s through a 5-cmID tube whose surface is maintained at 620 K. What length of tube is required?
Heat transfer Calculate the heat transfer rate in Btu/hr through the pipe ona stainless steel pipe with a length of 12m has an inner diameterof 10in and an outer diameter of 13in. The temperature of theinner surface of the pipe is 50°C and the temperature of theouter surface is 48°C. The thermal conductivity of the stainlesssteel is 187 W/m-°C. Show complete solution in a clear paper.
Steam flows at 300 °C through the given pipe with an inner radius of 5 cm and a wall thickness of 1 cm. The heat transfer coefficient of the pipe material is 30 W/m.°C'and the outer surface temperature of the pipe is T-300 °C at a'constant tempèrature of 220 °C. Assuming that h-18 W/m2C the heat transfer is only in the r direction, extract the equation expressing the temperature distribution and calculate the amount of heat discharged from the pipe to the environment. T- 220 °C BUHAR L- 3m
Fluid is flowing through a 20 mm inside diameter and 25 mm outside diameter brass tube at no leaking with temperature at 149oF and length of 10 m. Surface conduction of hot fluid is 5.2 W/m2-K and thermal conductivity of brass is 12.84 W/m2-K. Brass tube is covered by silica of 6 mm thickness with thermal conductivity of 13.84 W/m-K. Outside of it, is a fluid with 45oC with surface conductance of 3.2 W/m2-K. Find the heat transfer from the hot fluid with temperature of 149oF to fluid with temperature of 45oC.
Solve it pls.
The 0.5 m x 1.2 m wall of an industrial furnace is constructed from L = 0.15-m-thick fireclay brick having a thermal conductivity of 1.7 W/m-K. The temperature distribution, at an instant in time, is T(x) = a + bxwhere a = 140O K and b = -1050 K/m. Determine the heat fluxes, q, and heat rates, q,, at x = 0 and x = L, in W/m2 and W respectively. Do steady-state conditions exist? i W/m? i W/m? Ix=0 = i W Ix=L = i W
A spherical shaped vessel of 1.4 m diameter is 90 mm thick. Find the rate of heat leakage, if the temperature difference between the inner and outer surfaces is 220oC. Thermal conductivity of the material of the sphere is 0.083 W/m-K.
Its thickness is 1.18 m, its thermal conductivity is 2.75 W/m.°C and its surface area is 15m2Consider a wide plane wall. Inside of the base plateThere is a uniform heat flux produced on its surface with the help of the resistance wire inside.590 W/m2 on the left surface of the wall at x=0net heat fluxand the temperature on this surface was measured as 590 °C. On the wallassuming that there is no heat generation and that the thermal conductivity is constant;a) The differential equation for continuous one-dimensional heat conduction in the wall, andSet the boundary conditions.b) Solve the differential equation to obtain a relation for the temperature change at the wall.c) Calculate the heat loss rate from the wall.
I need the answer as soon as possible