- A conductor transfers heat of 3000 Ja in 6 seconds. Given cross it's length of 20 cm Hat it's cross-sectional area A is 550m². Determine the thermal conductivity of the material if the temperature difference acroSS the ends is 67°C.

- A conductor transfers heat of 3000 Ja in 6 seconds. Given cross it's length of 20 cm Hat it's cross-sectional area A is 550m². Determine the thermal conductivity of the material if the temperature difference acroSS the ends is 67°C.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Seh o I em Avertical cylinder with radlis 23 , ylinder height L eynat to i diameter, and surface temperature 70Cis standing iasalated Hout, and the sarrennding walls at 25 C. What is the antonnt of heat that lest by radiation "Watts" ben the vmiiity is .9 feiect one A 25 OD.113 E10101 NETE PREVIOUS PAGE CONTACTUS GET SOCIAL INPO
1wo isolated bodies Hie lame Matonal of masses M and 2M and initrally ot tem paratures T, and T respectioly, Contact until dhey Teach egril ubrum Shou that the gan are placed in th ermal equil in entrupy is Vbruum is AS =3 Mch/I 11 where c is Itra c heat Specific Capacity o ta matend. te material.
Conduction Homaworl s The in sode. of 3o'c, The well, 3D em thic h. Up house is your outside 5°e, You have e a t whick is- 3m against the vell Some inSulation which is 20 em thich. Givea that the cenduafivi fyr of the wall is 300%K ead the insulafion so %K caleulate is the temp betweey the layers, ared he béat trans ferr cate through the system, T- 30 T
The wall of a furnace comprises three layers as shown in the figuie. The first layer is tery (whose maximum allowable temperature is 1400°C) while the second laver is Tracto:y Chose maximum allowable temperature is 1093°C). The third layer is a plate of 6 35 od thermal contact. Steet plare To 6.35x3 45A 1370 C Concerntiation veluciy 37.8 C mass Siynes Figure. Layers in a composite furnace wall. e temperature To on the inside of the refractory is 1370°C, while the temperature T; on the side of the steel plate is 37.8° The heat loss through the furnace HnIlisexpectet tobe
Q1) A polished metal pipe (8 cm) owtside diameter and 350 K temperature at the outer surface is exposed to ambient conditions at 285 K temperature. The emissivity of the surface is 0.3 and the convection coefficient of heat transfer is 13.5 Wim2-deg. What would be the overall coefficient of heat transfer by the combined mode of convection and radiation” Q2 find the pressure point (1) if the amospheric pressure is(70kpajihl =0 2,h2=0.4,h3=0. ‘)(p. =13600kg/m3. poil=850kg/m3)
H.W: 10-02-2021: The exterior wall of a building consists of 100 mm thick face brick (k = 0.9 Wm¯'K'), 40 mm thick polystyrene insulating board (k 0.036 Wm'K¯), 125 mm thick concrete block (k = 1.8 Wm¯'K') and 15 mm thick interior gypsum board (k = 0.18 Wm K). The inside and outside convective heat transfer coefficients are 6.5 Wm K and 22.5 Wm K respectively. The outside air temperature is -5°C and the inside air temperature is 20°C. The wall is 3 m high and 15 m long. Calculate (i) the rate of heat loss through the wall,
The compartment below is used as a freezer of refrigerator compartment. Inner wall is at -10 C and outer wall is at 20 C. Insulator with a thermal conductivity of 0.040 W/(mK) is used to prevent the heat losses from the compartment. The shape is in square form with a side of 1.3 m and unit width into the page. Determine the amount of the heat load if the thickness of the insulator is 2 cm? *
It is designed in such a way that the internal temperature of a commercial heat treatment furnace can reach up to 165 oC. All surfaces of the furnace consist of firebrick (10 cm), insulation material and sheet metal (3mm) from the inside out. Given that the outdoor temperature is 22 oC, the outer sheet will be allowed to go up to 35 oC, which is a temperature that will not disturb in contact with hands. In this case, determine the insulation material thickness to be used. The thermal conductivity coefficient of the insulation material is insulation 0.066 W / m oC, 60 W / m oC for sheet metal and 115 W / m oC for firebrick. Indoor heat transfer coefficient will be accepted as 25 W / m2 oC and 12 W / m2 oC for outdoor environment.
i need the answer quickly
Required information A 14-cm x 20-cm circuit board houses on its surface 100 closely spaced logic chips, each dissipating 0.06 W in the environmentat 40°C. The heat transfer from the back surface of the board is negligible. If the heat transfer coefficient on the surface of the board is 10 W/m2.K, Determire the surface temperature of the chips in °C. (Round the final answer to two decimal places.
I got t=531.96 seconds is that right
Kindly give me right solutions with clear calculations.