please quickly, solve question12 Fig. 1 shows an oscillator circuit using 555 timer, with RA = 1.5KQ, RB =2.5KQ Vcc= 12 V, and C= 0.7215uF. Assume the diode is ideal, then123If the diode is disconnected, then456The charging time (T,) (in ms)The duty cycle (ratio)The frequency of the output signal (in Hz)1016The discharging time (T₂) (in ms)The duty cycle (ratio)The frequency of the output signal (in Hz)V R₁RARB11+VccDischargeThresholdTriggerGroundD,Fig 3Reset555 Output+125-12+Vcc45voVEEA1.250.375666.7The minimum output voltageDraw to scale the transfer characteristics.Draw to scale the input and the output signals when Vin is a triangle wave of 8 Vp-p1.50.615500Voltage transfer c/cwwREVERFig. 1Fig. 2Consider the sweep generator circuit shown in Fig. 2 where RE = 4KS2, RB = 4.7K2, VEE=30.7V, VBB= 20V, and C= 0.5 uF.The control signal (v) has a pulse duration of 0.5ms, a frequency of 500Hz, and a +12V amplitude. Then72.53.589The emitter current I (in mA)The charging time of the capacitor (in ms)2.5The peak voltage of the capacitor (Vp)6.0The minimum value of Rg that we can use and still obtain a linear sweep 1.5waveform (in K2)Consider a Schmitt trigger circuit with ± VSAT = 12 V, Vur=4V, and Vir=0 V. This circuit is modified to be an oscillatorcircuit by adding C= 3.46 µF and R=2 KS2. Then11 The charging time (Tch) of this circuit (in msec) is2.812 The discharging time (Tdisch) of this circuit ( in msec ) is3.0Consider the circuit shown in Fig. 3 where Vzi = 3.3V, VA= 4.3V, and ± VSAT = ±12 V. Then13 The maximum output voltage4.05.014-4.0- 5.015BC0.51.00.667 0.333307.85001.44.01.750.6307.71.250.54002.03.010.51.82821.59.01.24.21.0D0.750.54001.00.75666.7R₂12-0.7LI3.02.07.52.11995.62.0Yourans.0.7- 12input and output

12) The circuit of the Astable multivibrator is given as Given data are…

Consider a Schmitt trigger circuit with ± VSAT = ± 12 V, Vur=4V, and VLT=0V. This circuit is modified to be an oscillator circuit by adding C= 3.46 µF and R=2 KQ2. Then 11 The charging time (Tch) of this circuit (in msec ) is 1.4 2.8 4.0 3.0 12 The discharging time (Tdisch) of this circuit ( in msec ) is Consider the circuit shown in Fig. 3 where V=3.3V, V=4.3V, and + Yer= +1? Than 4.2 1.0 5.6 2.0

Consider a Schmitt trigger circuit with ± VSAT = ± 12 V, Vur=4V, and VLT=0V. This circuit is modified to be an oscillator circuit by adding C= 3.46 µF and R=2 KQ2. Then 11 The charging time (Tch) of this circuit (in msec ) is 1.4 2.8 4.0 3.0 12 The discharging time (Tdisch) of this circuit ( in msec ) is Consider the circuit shown in Fig. 3 where V=3.3V, V=4.3V, and + Yer= +1? Than 4.2 1.0 5.6 2.0

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

I need the answer as soon as possible
Analyze the circuit below. D. With the following given values, E 5V E- 10V, E 10V, R= 20, Ry 32 R= 40 R, = 5N, Solve for: (Input answers up to two (2) decimal places, but solve with four (4) decimal places to limit inaccuracies.) Note: Do not input signs. Answers should only contain magnitude and don't forget to include the unit. No spaces between characters. Final answers in two (2) decimal places and if the answer is a whole number, do not include decimals. 1 1 = 2 1
Solve step by step. Please solve fast.
Please click on pic to open it
Need 100% Perfect answer.
Problem #4 Implement the function F = A'B' + AC + A’C'D using ONLY one multiplexor (of any size). In order to receive credit, your answer must be correct AND use good style. This includes good documentation practices – your implementation should be easy to verify. Needlessly inefficient circuits will be marked down.
The block diagram reduction process takes more time for complicated systems. Because we have to draw the (partially simplified) block diagram after each step. In regards to this, how you can overcome this drawback?
Please solve the question with all possible steps with a simple explanation, the question is in the attachments.
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
Please solve the question with all possible steps with a simple explanation, the question is in the attachments.
Please solve the question with all possible steps with a simple explanation, the question is in the attachments.
if possible, kindly the solution isnt handwriting ( text through keyboard ) is much appreciated and readable* Course: EE 350 ( System Dynamics and control ) Major: electrical engineering Note: Bartleby expert solved first three sub-parts A,B and C. and told me to post the question again so the rest of the solution could be solved ( D, E, F )