Consider a metal single crystal oriented such that the normal to the slip plane and the slip direction are at angles of 43.1° and 47.9°, respectively, with the tensile axis. If the critical resolved shear stress is 20.7 MPa (3000 psi), will an applied stress of 45 MPa (6500 psi) cause the single crystal to yield? If not, what stress will be necessary?

Consider a metal single crystal oriented such that the normal to the slip plane and the slip direction are at angles of 43.1° and 47.9°, respectively, with the tensile axis. If the critical resolved shear stress is 20.7 MPa (3000 psi), will an applied stress of 45 MPa (6500 psi) cause the single crystal to yield? If not, what stress will be necessary?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The diagram below shows a microscopic metal rod with a single crystal structure whose orientation is indicated by the inset. A force of F = 14.9 N is applied to the rod. The cross-sectional area is 1.1 mm². Calculate the shear stress along the close-packed direction. Dogo ooooo a. 4.65 MPa O b. 6.08 MPa c. 5.09 MPa O d. 4.04 MPa O e. 5.53 MPa
Question-8. . A cylindrical metal specimen with a diameter of 16 mm and length of 88 mm is to be subjected to a tensile stress of 80 MPa; at this stress the resulting deformation is elastic. (a) If the elongation is less than 0.058 mm, which of the metals in the table can be considered as candidates? Why ? (b) If the maximum permissible diameter decrease is 0.0012 mm when the tensile stress of 68 MPa is applied, which of the metals satisfy the criterion in question (a) are the suitable candidates? Why ? Metal Shear Modulus / GPa Modulus of Elasticity / GPa 69 Poisson's Ratio Al 25 0.33 Cu 110 46 0.34 Mg 45 17 0.29 Ni 207 76 0.31 Ti 107 6.5 0.34 W 407 23.2 0.28
Consider an iron single crystal with CCC crystal structure oriented in such a way that a tensile stress is applied to the along one direction [010]. a) Calculate the shear stress resolved along a plane (110) and a direction when a tensile stress of 52 MPa is applied. The normal to the slip plane forms 45° with traction direction. the direction of slip forms 55º with the traction direction. b) If the slip occurs in one plane (110) and in one direction and the critical resolved shear stress is 30 MPa, calculate the magnitude of tensile stress that must be applied to initiate the flow.
Pravinbhai
Consider a single crystal of a hypothetical metal that has the BCC crystal structure. A stress of 50 MPa is applied in the [101] direction of the BCC unit cell.a. Determine the most favourable slip direction for the (011) slip plane of the BCC unit cell. ⟨111⟩ is the family of directions with the highest linear density in the BCC unit cell.b. If τcrss = 27.5 MPa, determine if the single crystal yields. If not, what stress level is required?c. What is the minimum stress at which the BCC single crystal yields?
3. An uncold-worked brass specimen of average grain size 0.01 mm has a yield strength of 150 MPa (21,750 psi). Estimate the yield strength of this alloy after it has been heated to 500°C for 1000 s, if it is known that the value of σo is 25 MPa. (Note that the axis has logarithmic scale). Grain diameter (mm) (Logarithmic scale) 1.0 0.1 0.01 1 10 850°C 800°C 700°C 102 Time (min) (Logarithmic scale) 600°C 500°C 103 104
Problem 5. Starting with a 2-inch diameter rod of brass, we would like to process 0.2-inch diameter rods that possess minimum yield strength of 40 ksi and a minimum elongation to fracture of 40%, (see the following figure). Design a process that achieves that. 120 70% Cu-30% Zn 100 Tensile strength 80 60 60 Yield strength 40 40 20 20 Elongation 10 20 30 40 50 60 Percent cold work Tensile strength and yield strength (ksi) Elongation percent
What is the maximum value of KIc as per LEFM that can be determined from experiments on a 20 mm thick plate? yield strength= 500 MPa, E= 210 GPa, poission ratio=0.3.
In an engineering application, the material is a strip of iron with a fixed crystallographic structure subject to a tensile load during operation. The part failed (yielded) during operation and needs to be replaced with a component with better properties. You are told that two other iron strips had failed at yield stresses of 110 and 120 MPa, with grain sizes of 30 microns and 25 microns respectively. The current strip has a grain size of 20 microns. The diameter of the rod is 1 mm and the load applied is 100 N. What is the yield stress of the new part C and would you recommend it for operation? Select one: a. O b. 129.5, yes C. 133.5 MPa, yes e. 120.5 MPa, no d. 140.5, no 123.5 MPa, yes
(b) The yield stress for a metal changes from 450 Nmm-2to 610 Nmm-2 when the average grain diameter decrease from 0.043 mm to 0.022 mm. Determine the yield stressfor the same metal with an average grain diameter of 0.030 mm.
Need help on this