connecte lameter bolts in each flange, as sho fFy 448 MPa, and Ae = 0.90An, compute the following. a. The design strength for LRFD. p. The allowable strength for ASD. Properties of C12 x 30 A = 5,690 mm Dr= 50 mm d = 304.8 mm iw = 13 mm = 12.7 mm P

connecte lameter bolts in each flange, as sho fFy 448 MPa, and Ae = 0.90An, compute the following. a. The design strength for LRFD. p. The allowable strength for ASD. Properties of C12 x 30 A = 5,690 mm Dr= 50 mm d = 304.8 mm iw = 13 mm = 12.7 mm P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the bolted tension member is shown in the figure. Determine the effective area, Ae. Given, x = 1.68 inch, Ag = 5.75 inch?. (4)- S/8" A325N bolts L6 x 6 x 1/2 -Tu 3" 3" 3"
Bottom chord of truss is composed of two angle bars each having a dimension of 185 mm x 146 mm x 8.7 mm. Between them is a gusset plate, 9.5mm thick. At each end of joints, four 19mm-dia. bolts are fastened along the gage line, having an edge distance of 44 mm and 59mm pitch. Use A36 steel Fy 248 MPa Fu = 400 MPa %3D spacing of bolt = 68.9 mm %3D 9 5mm thick gunset plate edge dist Compute the capacity of the bottom chord based on block shear strength, in KN. uad
A C8 × 11.5 is connected to a gusset plale with 22 mm diameter bolts as shown. The steel is A572 Grade 50. If the member is subjected to dead load and live load only, what is the total scrvice load capacity if the live-to-dead load ratio is 3? Assume that Ae = 0.85Ap. a. Use LRFD. b. Use ASD. Properties of A572 Grade 50: Fy = 345 MPa C8 × 11.5 Fu = 448 MPa Properties of C8 x 11.5: Ag = 2,181 mm? br = 57.4 mm d= 203.2 mm Lw = 5.6 mm lf = 9.9 mm
The tension member shown in Figure P3.2-5 is a PL 1/2 x 8 of A36 steel. The member is connected to a gusset plate with-11/8 inch- diameter bolts. It is subjected to the dead and live loads shown. Does this member have enough strength? Assume that Ae = An. оооо D=95t L=9k PL ½x8
A WT 8×13 of A992 steel is used as a tension member. The connection is with 7/8-in. diameter bolts as shown in Figure. Compute the nominal block shear strength. Note: A992 steel Fy = 50 ksi Fu = 65 ksi Ubs = 1.0 %3D 12"+3">|| 42" 7.85" 0.25" Round your answer to 3 decimal places.
The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with 7⁄8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16’’ Use: Consider deformation at the bolt hole Compute the nominal strength in bearing on Gusset plate only (since this will govern, it has smaller thickness than the main member PL ½ x 6)
The tension member shown is a channel C12 x 25 of A572 steel with F,= 345 MPa and F,= 450 MPa, is subjected to a service DL= 275 KN and a service LL= 560 KN. Use equation for U. Use LRFD. 65r 65m65 -22mm bolts O O o O C12x25 O O O 0 Check the adequacy of the channel tension member.0
Read the situation carefully and answer the problem with complete, clear, and correct solution. A PL 3/8 x 7 tension member is connected with three 1-inch-diameter bolts, as shown in Figure P3.2-1. The steel is A36 Fy-36ksi, Fu=58ksi. Assume that Ae = An and compute the following. a. The design strength for LRFD. b. The allowable strength for ASD. PL 3 x 7 FIGURE P3.2-1 "There is no elevator to success, you have to take the stairs." - Zig Ziglar God bless. Ⓒ
A C8 x 11.5 is connected to a gusset plate with 7/8 inch diameter bolts as shown in Figure P3.2-3. The steel is A572 Grade 50. If the member is subjected to a dead load and live load only, what is the total service load capacity if the live to dead load ratio is 3? Assume that Ae=0.85An. Use LRFD and ASD.
A double-angle shape, 2L7 3 4 3 3⁄8, is used as a tension member. The twoangles are connected to a gusset plate with 7⁄8-inch-diameter bolts throughthe 7-inch legs, as shown in Figure P3.4-5. A572 Grade 50 steel is used.a. Compute the design strength.b. Compute the allowable strength.
A C9x20 is used as tension member connected to a gusset plate of ½ in thick (Figure 5). The member has to resist service dead load and live load of 40 kips & 80 kips respectively. Steel used is A36. Assume connection is adequate in block shear. Design the bolted connection (check slip critical, shear and bearing strength). Use ASD. t = W" C9 × 20 Figure # 5
A built-up section was made using PL414x12mm thk plates as shown in the figure below. It is pinned at both ends with additional support against weak axis at middle point. Assume A50 steel. PL414x12 DO Section W16x67 L x-axis a) Calculate moment of inertia at both axes in mm*. b) Determine the design compressive strength in kN if L-3m. c) Find the design compressive strength in kN if L=18m. Elevation y-axis