coefficient of discharged,cd actual discharge Qa0.96184 7.6212x10^-41.04815 1.3100x10^-30.98280 1.8059x10^-31.03660 2.6597x10^-31.05895 0.017080224 Graph 2. Variation of coefficient of discharge, Ca with actual discharge, Qa-T--T--T-Actual discharge, Qa (m³/s)Coefficient of discharge, Ca

Given: Data for actual discharge and coefficient of discharge To find: To form a graph

Answered: coefficient of discharged,cd…

coefficient of discharged,cd actual discharge Qa 0.96184 7.6212x10^-4 1.04815 1.3100x10^-3 0.98280 1.8059x10^-3 1.03660 2.6597x10^-3 1.05895 0.017080224

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Fluid with a density of 800 kg/m^3 and velocity of 9.375 m/sec flows through a pipe diameter of 20 mm pipe and wall roughness of 0.02 mm. Using Moody chart, determine the approximate friction factor if the viscosity of the fluid is 0.015 kg/(m-sec)? Moody chart 10 0.05 Sato 0 025 :0.01 0.007 F0 001 0.0001 smooth 0.00005 Re [-) O 0.025 O 0.055 O0.035 O0.015 O 0.075 RELATIVE ROUGHNESS O OO0
HAH 5.6.1. The following table provides the results of a pump performance test. Discharge (gpm) Pump head (ft) 0 150 200 145 400 135 600 120 800 90 1,000 50 a. Plot the pump characteristic (performance) curve Plot the characteristic curve for two pumps in series C. Plot the characteristic curve for two pumps in parallel b. d. What pump configuration would work for required flow of 1,700 gpm which must overcome a head of 80 ft? What pump configuration would work for required flow of 1,700 gpm which must overcome a head of 160 ft? e.
.com/c/Mjc5MTg3Nj12NzEz/a/M]950TUXNTUWMTE2/details Problem 3: A large pressurized tank filled with air discharges into the atmosphere. The flow path is a short and frictionless smooth pipe connected to a discharge nozzle. Find a) the flow rate of air and b) pressure in the pipe for the given data. Ignore all frictional losses, including head losses at the entrance to the pipe, at the bend, and at the nozzle. Prank (kPa): 110.0 Dpipe (m): 0.040 P (kPa): 101 atm Nozzle (m): 0.015 Tatm (C): 20 Air
Assessment Simplify. (y^(-3))^(7) Write your answer without using nega
The figure below shows the stress strain diagram of a cortical bone, with initially rectangular cross section of 15 x 20 mm2, and length of 10 cm. using this figure determine: a) The elastic modulus b) The yield strength c) The ultimate strength. d) The corresponding ultimate true stress, if you know that the instantaneous cross section was at this point was 12 x 17 mm?. e) The deformed length corresponding to the ultimate strength. f) The poison's ratio corresponding to the ultimate strength for the following two cases: a. Use the 15 mm as the undeformed specimen width. b. Use the 20 mm as the undeformed specimen width
A Pitot-static tube is used to measure the velocity of 68°F water (p 62.32 lbm/ft', H=2.09 x 10 1bf-s/ft) flowing in an open channel. A differential pressure of 2.36 in. of water is measured. Determine the corresponding water velocity (ft/s). %3D
Water flows from a 20-mm-diameter pipe with a flowrate Q as shown in the figure below. What is the approximate diameter of the water stream, d, in units of cm, if the distance below the faucet is, h=2 m, and Q = 0.003 m³ /s? 20 mm O a. 1.83 m b. 2.07 m O c. 3.29 m d. 4.66 m O e. 5.29 m
Answers (a) er=15.30-250.2/r^2 , etheta=15.30+250.2/r^2 (b) delta c = 8.12x10^-4 in
1.28. The performance curve for the fan of Problem 1.27 can be approx- imated by a straight line through its BEP (using techniques devel- oped in Chapter 7). The curve is Aps = 4488 – 166Q, with ApT in Pa and Q in m³/s. If this fan is connected to a 1-m dia- meter duct (f = 0.045) whose length is 66 m, what flow rate will result? %3D
A pressure gauge at elevation 8 m at the side of a tank containing a liquid reads 80 kPa. Another gauge at elevation 4 m reads 120 kPa. Compute for the Density a. 4077.47 kg/m^3 b. 815.49 kg/m^3 c. 1019.37 kg/m^3 d. 5096.84 kg/m^3
The flow rate of a hydraulic fluid with a Sg of 1.08 through a 2-in. I.D. orifice is 50 gal/min. If the pressure drop across the orifice is 5 lbf/in.", what is the discharge coefficient?
A pipeline 0.3 m in diameter divides at a Y into two branches of 200 mm and 150 mm in diameter. If the velocity in the main line is 3 m/s and the velocity is 2.5 m/s in the 200 mm branch, what is the flow rate in the 150 mm branch? 0.212 m^3/s 0.134 m^3/s 0.0785 m^3/s 0.652 m^3/s Activate Windows Go to Settings to activate Windo Question 6 of 10