A pipeline 0.3 m in diameter divides at a Y into two branches of 200 mm and 150 mm in diameter. If the velocity in the main line is 3 m/s and the velocity is 2.5 m/s in the 200 mm branch, what is the flow rate in the 150 mm branch? O 0.212 m^3/s O 0.134 m^3/s O 0.0785 m^3/s O 0.652 m^3/s Activate Windows

A pipeline 0.3 m in diameter divides at a Y into two branches of 200 mm and 150 mm in diameter. If the velocity in the main line is 3 m/s and the velocity is 2.5 m/s in the 200 mm branch, what is the flow rate in the 150 mm branch? O 0.212 m^3/s O 0.134 m^3/s O 0.0785 m^3/s O 0.652 m^3/s Activate Windows

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The pressure loss p in a pipe is related to the flow rate Q by the equation P = KQ^n, where K and n are constants. If K = 190 x 10³determine the value for n when a flow rate of Q = 0.04 m³/s causes a pressure loss of 180 Pascals.
Calculations involving retention time involve the following formula, T =, where V is volume and Q is flow rate. Often times, you will be required to calculate the volume of more than one tank and determine a rate of flow, given a total retention time. Tank 1 Tank 2 Let's assume that the total retention time for the entire system is 55 minutes, and we want to know the inlet flow, given the dimensions of tank 1 are : 14m x 10m x 3 m, and tank 2 are: 5m x 10m x 3 m. Calculate the inlet flow.
Q1/ Water flows in the pipe shown in Fig. No. (1) from point No. (1) to point No.(2) at flow rate of Q = 0.1414 (m³/s). If P¡ is 70 (Bar), P2 is 9.81 (Bar), f=0.02 and length of pipe from point No. (1) to point No.(2) is 15.67 (km). (1) Find the diameter of the pipe (2) Find flow velocity in the pipe. (3) Draw the H.G.L. of flow in the pipe. P2 =9.81 (Bar) p1 = 70 (Bar) 400 m Reference Line 30° Fig.(1)
(1) Medium lubríčating oil, sp gr 0.860, is pumped through 300 m of horizontal 50.0-mm 流量 pipe at the rate of 0.00140m³/s. If the drop in pressure is 200kPa, what is the coefficient 殺度 of viscosity of the oil? E R. -Fluid layer 杉性狼体 Vo (2) A wide moving belt passes through a container of a viscous liquid. The belt moves vertically upward with a constant velocity, Vo, as illustrated in Fig. 1. Because of viscous forces,the belt picks up a film of fluid of thickness h, Gravity tends to make the fluid drain 物流 down the belt. Determine an expression for the average velocity of the fluid film as it is dragged up belt. Assume that the flow is laminar, steady and uniform. ち上ける。 Fig. 1
Water flows from a 20-mm-diameter pipe with a flowrate Q as shown in the figure below. What is the approximate diameter of the water stream, d, in units of cm, if the distance below the faucet is, h=2 m, and Q = 0.003 m³ /s? 20 mm O a. 1.83 m b. 2.07 m O c. 3.29 m d. 4.66 m O e. 5.29 m
1.28. The performance curve for the fan of Problem 1.27 can be approx- imated by a straight line through its BEP (using techniques devel- oped in Chapter 7). The curve is Aps = 4488 – 166Q, with ApT in Pa and Q in m³/s. If this fan is connected to a 1-m dia- meter duct (f = 0.045) whose length is 66 m, what flow rate will result? %3D
2. A fluid moves in a steady flow manner between two sections in a flow line. At section 1: A_1 =2 ft^2; 9_1 = 100 fpm; V_1 = 4 ft^3/lb. At section 2: A_2=2 ft^2; p_2=0.20 lb/ft^3. Calculate the speed at section 2 in ft/min or fpm %3D
Elevation = 100 ft D¸ = 1 ft (1) l (1) e, = 1000 ft D2 = 1 ft lz = 500 ft B V Elevation = %3D 20 ft (2) D3 = 1 ft (3) Elevation = l3 = 400 ft O ft Three open reservoirs are connected by pipes as shown above. It is assumed that the pipe diameter is equal to the friction factor of 0.03. Because theratio of the LIDpipe is large, the minor losses are ignored. Determine the flow in or out of each reservoir! Draw with sketch 5.
A pump has a flow rate of 0.5 m3/min. The pump head is 12 m. (a) Determine the pump head in m^2/s^2. Answer Check: 118 m^2/s^2 (b) Determine the pressure change across the pump. Answer Check: 118,000 Pa (1Pa = 1kg/m s^2) (c) Determine the work required for a 100% efficient pump. Answer Check: 980 W (d) Determine the work required for a 85% efficient pump. Answer Check: 1.15 kW
Air flows through a Venturi channel of rectangular cross-section as shown in Figure 1. The constant width of the channel is b and the height at the exit is 0.04 m. Assume the flow is incompressible and inviscid. Use ρ water = 1000 kg/m^3 and ρ air = 1.2 kg/m^3. Use g = 9.81 m/s^2. calculate the volumetric flow rate, in m3/s, for:b= 0.08 m, h2 = 0.03 m and P2 = -500 Pa (Gauge)
A water pipe is laid on a slope of 1 in 40. The pipe is 50 m long. Water flows upwards at the rate of 0.06 m^3/s. The inlet diameter at the lower end is 200 mm. The diameter at the outlet is 400 mm. Determine the pressure at the lower end if the pressure at the higher end is 24.525 N/cm^2. *32.198 N/cm^2*26.075 N/cm^2*21.238 N/cm^2*25.580 N/cm^2
Based on the rotor shown below, estimate the mass flow rate through the rotor if the density of the fluid is 800 kg/m and the height of the blade is 0.15 m. V2 = 277 m/s az = 30° %3D U2 = 325 m/s W2 U 152 m/s V = 121 m/s R2 = 0.5 m a = 450