CLO 1: It is a torsional parameter equal to twice the product of the areaenclosed by the centerline of the tube and the shear flow.O Angle of IwistO TorqueO Modulus of RigidityO lorsional Suress CLO 2: The first moment of area, Q is maximum at:O both maximum and minimum "b"O neither of the choicesO minimum "b"Omaximum "b"

The name shear flow (or shearing flow) refers to a type of fluid flow that is caused by forces…

Answered: CLO 1: It is a torsional parameter…

CLO 1: It is a torsional parameter equal to twice the product of the area enclosed by the centerline of the tube and the shear flow. O Angle af Iwist O Torque O Modulus of Rigidity O lorsional Stress

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 52-kip force acts on a machine part at point A as shown below. The diagram shows the internal normal force, shear force and bending moment acting on a particular RECTANGULAR Cross section. -30in N 10in 26in F=52 kip The value of the bending moment M you would use to find the bending stress on a stress element located 2 inches up from the bottom of the rectangular cross section is closest to: 264 kip-in O a. 408 kip-in Ob. 1,464 kip-in O c. 1,608 kip-in
A beam ABC with an overhang from B toC supports a uniform load of 200 lb/ft throughout itslength (see figure). The beam is a channel section withdimensions as shown in the figure. The moment of inertiaabout the z axis (the neutral axis) equals 8.13 in4.(a) Calculate the maximum tensile stress σt andmaximum compressive stress σc due to theuniform load.(b) Find the required span length a that results inthe ratio of larger to smaller compressive stressbeing equal to the ratio of larger to smaller tensilestress for the beam. Assume that the totallength L =a + b = 18 ft remains unchanged.
Mechanics of Deformable Bodies. Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that d1 5 30 mm and d2 5 50 mm, find the average normal stress at the midsection of (a) rod AB, (b) rod BC.
Problem 2 The rigid bar is plnned at A and held by two flexible bars at E and C. The load P Is applled at B. The two flexible bars FE and DC each have a diameter of 1 In. The flexible bars are elastic- perfectly plastic with a yleld stress equal to 20 ksl and a yleld strain of 0.001. Determine the following: The load R, at first yleld and the corresponding deflection at B, &, The ultimate load Pu and the corresponding deflection du The permanent deflection and residual stresses in each rod if the ultimate load is removed Construct P - A curve showing yield, ultimate and permanent deformation o (ksi) 1 ft E F 1 ft1 ft 20 B P e (in./in.) 0.001 1 ft D 2 ft 1 ft A
2. Determine the normal stress in members BD, AC, and BC in the truss shown. The cross- sectional area of each member is 1500 mm2. Indicate whether the stresses are tensile (T) or compressive (C). Use 2 decimal places in every solved value. 10 m 10 m 10 m K 6 т H 6 т 15° 15° 50 kN 40 kN E F 6 т C D б т A B
5 - An aluminum circular shaft, fixed at both ends, is loaded by torques applied at points B and C, as shown in the figure. The bar material has a shear modulus G = 85 GPa. Plot the maximum shear stress and angle of twist along the length of the shaft. A D TB 0.5m Tc 0.9m с 0.4m 40mm ↑ TB-10KN-m Tc=15KN.m
Mechanics of Deformable Bodies 6 in. in.- 5 in. 4 in. A steel tube with the cross section shown carries a torque T. The tube is 6ft and has a constant wall thickness of 3/8in. (a)Compute the torsional stiffness k=TTO of the tube. (b) If the tube is twisted through 0.5°, determine the shear stress in the wall of the tube. Use G=12x 106psi.
Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Determine the magnitude of the force P (in lb) for which the tensile stress in rod AB is thrice the magnitude of the compressive stress in rod BC if Q = 20.11 lb.
The plate has a thickness of 20 mm and the force P = 5 kN acts along the centerline of this thickness such that d = 150 mm. (Figure 1) Figure d‡ 200 mm a 1 of 1
6- A circular shaft is composed of a steel core and a brass covering, as shown in the figure. Under the applied torque, what is the maximum shear stress in each material? The composite shaft is attached to a wall at A. B O T= 5 KN•m Steel core r=15mm G=78 GPa bross cylinder ro=20mm (outer diameter) G=39 GPa
a. The beam weighs 3600N. Draw the V and M diagram. b. Assume we do not know the weight of the beam the solid steel bar has a square cross section of side b and is supported as shown. We know that density of steel is 7860 kg/m, calculate the dimension b for which the maximum normal stress due to bending is 50 MPa. C D I-KE -1.2 m-1.2 m 1.2 m B
1. An axial force of 250 kN is applied to the assembly shown, made of cylindrical brass core surrounded by an aluminum shell. The axial force is applied through rigid end plates. a) Determine the normal stress in each of the metal components, given that Ebrass = 105 GPa and Ealum = 70 GPA. 100mm b) What is the axial deformation of the assembly? 200mm 200mm