80 mm20 mm7 mmMMClick to see additional instructionsCalculate the minimum Safety Factor if the radius r = 5mm and M= 17.5 Nm. The material is mild steel with Sy = 220 MPa.Fill in the answers below and make sure of the unit.1. r/h =2. w/h =3. k=

Answered: Image /qna-images/answer/74027b62-b102-47e3-904c-28a7d3c9424d.jpg

Answered: Click to see additional instructions…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the Brinell hardness number of the material if the indenter diameter is 10mm and the produced indentation was 5.12mm. The standard load of 3000kE was applied. (attach your solution)
4. The mechanical properties of a given titanium alloy (Ti-6Al-4V) are E = 114 GPa, σy = 880 MPa and Kic = 75 MPa√m. What is the approximate plastic zone size? How large must a part be made if we want to test its K₁ using LEFM?
Fill in the blanks.
Please provide the solution to the correct answer shown in the image. If your solution does not match the correct answer stated in the image, a downvote will be given.
. A machine member is subjected to fluctuating stress 0=0, cos(8nt). The endurance limit of the material is 350 MPa. If the factor of safety used in the design is 3.5, then the maximum allowable value of o, is MPa (round off to 2 decimal places). 0
I am not sure what I am doing wrong. Please help, thanks!
The A-36 steel bolt is tightened within a hole so that the reactive torque on the shank AB can be expressed by the equation t = (kz²/³) N-m/m, where z is in meters. A torque of T-50 N-m is applied to the bolt head. Assume the shank has a constant radius of 7 mm. The shear modulus of elasticity for A-36 steel is 75 CPa. (Figure 1) 50 -7-50 Nm Determine the constant k. Determine the amount of twist in the 50-mm length of the shank
The engineering stress-engineering strain tensile curve for a stainless steel type 304 alloy is shown. Calculate the constants K and n for the true stress and true strain curve before necking (or = K (&)"). Engineering Stress (MPa) 1000 900- 800- 700- 600- 500- 400- 300- 200- 100- of 0.0 02 0.4 Enginering Strain (mm/mm) 0.6 0.8 1.0
If a key material has an ultimate strength of 120 ksi and a yield strength of 80 ksi and factor of safety N=2, what would be the design compressive stress in ksi? (a) 40 ksi (b) 60 ksi (c) 160 ksi (d) 240 ksi
For a large plate, the geometry factor, f, is 1.03. Suppose a steel casting alloy has a critical fracture toughness of 78,886 psi*in1/2. The steel will be exposed to a stress of 40,295 psi during service. Calculate the minimum size of an edge crack that will grow. Repeat the calculation for Al2O3 with a fracture toughness of 1,600 psi*in1/2. How many times larger is the minimum size edge crack in the steel versus the alumina?
Thank you for answering this question. Please you specify each step as soon as possible. Good Luck! Thank You. Find the maximum biaxial stress,ox= -20, oy= -30, o > 0, that one can apply to a 60° lamina of glass/epoxy. Use maximum stress theory. Strength values of glass/epoxy: (01Jult = 1062 MPa, (01Jult= 610 MPa, (02")ut = 30 MPa, (02)ult = 118 MPa, (T12)ult = 72 MPa
A steel rod with a cross-sectional area of 150 mm² is stretched between two fixed points. The tensile load at 20°C is 5577 N. What will be thestress at 25°C?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Click to see additional instructions Calculate the minimum Safety Factor if the radius r= 5mm and M= 17.5 Nm. The material is mild steel with Sy = 220 MPa.