diameter bar has been machined from 1050 hot rolled steel at 600C. The bar will be subjected to a fluctuating tensile load varying from 100 to 500kN. Calculate the fatigue factor of safety according to the Modified Goodman fatigue criterion, ASME

Q: A solid round bar with diameter of 2 in has a groove cut to a diameter of 1.8 in, with a radius of…

A:

Q: Estimate the endurance strength of a 1.5-in-diameter rod of AISI 1040 steel having a machined finish…

A: Data Given : d = 1.5 inAISI 1040 material steel machined surface and heat treated.Tensile strength =…

Q: Given: A ground steel rod with known diameter d is operating at temperature T. You are designing…

A:

Q: A machine member is to be designed to operate under a stress ranging from 10,000 psi compression to…

A:

Q: pls find box ur answer Determine the value of the von Mises stress at point A. The von Mises stress…

A: The values are P=4 kN, F=0.55 kN, T=25 Nm The yield stress is Sy=280 MPa The length of the pipe is…

Q: elongations is 1.0 mm. The total length of the test specimen after 4,000 hours is 105 mm. If the…

A: To obtain the solution of the above question, first of all, we will determine the creep rate of the…

Q: 2. A l-in diameter rotating solid round bar has a groove 0.1-in deep with a 0.1-radius machined into…

A: Given data as per question Bending moment =1000 lbf. in f =0.9  q = 0.8 Calculations tensile…

Q: the figure is subjected to a completely  reversed axial load fluctuating between 28 kN in…

A:

Q: The figure below is subjected to a load fluctuating between Pmin and Pmax. Calculate the factor of…

A: Write the given values along with the suitable variables.

Q: pls solve fast A piston rod subjected to a total load of having cyclic fluctuations from 10 kN in…

A: Step 1:To determine which material to choose for the piston rod, we'll need to perform fatigue…

Q: 4. A bar of steel has minimum properties of Se=40 kpsi, Sy = 60 kpsi, and Sut = 80 kpsi. The…

A:

Q: Two steels are being considered for manufacture of as-forged connecting rods. One is AISI 4340…

A: We need to find out the advantages of using these two materials.4340 Steel.Uncorrected endurance…

Q: The bars, shown in sketches (a) and (b), are made from cold-drawn, AISI 1050 QT at 425 °C medium…

A:

Q: An S-N plot from fatigue testing of a steel is provided below. Use the plot to determine the…

A: INTRODUCTION: S–N curves can be measured by applying a constant amplitude and mean, harmonic load on…

Q: A flat-rolling operation of 250 mm wide alloy stee Calculate roll torque

A: GIVEN: **Width (Wt)=250mm **Diameter of rollers (D)=600mm **Height before rolling (ho)=30mm**Height…

Q: (14) The figure shows a formed round-wire cantilever spring (Sut = 188.1 kpsi) subjected to a…

A: Given that, Sut=188.1 kpsi,Fmax=30 lbf,Fmin=15 lbf,…

Q: A strain gauge mounted at a potentially critical point in a steel part has recorded the stress…

A: To Find : the fatigue life in problem be reduced if a mean stress of  10 ksi is added to the stress.…

Q: 8. Refer to the figure below. Even though the cyclic loading accidentally caused the stresses to…

A:

Q: A bracket is under a loading condition shown below. It's made from a steel with yield strength (Sy)…

A: Write the given information.

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.