ick as shown in the ield strength of the 260 N/mm², and plastic moment of nape factor.

Q: A very thick structure is subjected to certain traction boundary conditions on its surface. The…

A: As asked only the first three are solved. φ(x,y)=sinxAx2e-y+Bey

Q: 290 J of energy is transferred to a system consisting of 2.0 moles of an ideal gas. If the volume of…

A:

Q: For the composite areas shown, determine the moment of incrtia with respect to the centroidal ахes.

A:

Q: y

A:

Q: (b) An automotive clutch driven plate is clamped between a fly- wheel and a sprung pressure plate.…

A: Friction Clutches : Friction clutches are mechanical devices which are used to transmit power from…

Q: Determine the force in members BC, FC, and FE and state if the members are in tension or…

A: from the FBD,

Q: Steam is used in an ideal combined reheat and regenerative system as shown in figure A (turbine and…

A:

Q: 4.18 What is the composition, in atom percent, of an alloy that contains 44.5 lbm of Ag, 83.7 lb,m…

A: Given data:         mass of Ag= MAG= 44.5 lbm         mass of Au= MAU = 83.7 lbm         mass of Cu…

Q: Gear 2 (pinion) runs at 1800 rpm ccw and transmits 3.5 kW to frictionless, idler gear 3. The…

A: Given:- P=3.5kW m=2mm Pressure angle=20° N=1800rpm To find:- g) Torque on gear 4

Q: 1. The tower is held in place by three cables. If the force of each cable acting on the tower is…

A:

Q: 1 Legs of a pneumatic system are generally equipped with and work stations receive air which meets…

A: This question is based on the concept of legs of pneumatic system and SUS.

Q: A vacuum gauge mounted on a condenser reads 0.56 m Hg. What is the absolute pressure in the…

A:

Q: Problem 3: Find the centroid C(x, y, 7) of the machine element shown in the figure below with…

A:

Q: THE SYSTEM SHOWN BELOW IS IN EQUILIBRIUM IF THE WEIGHT OF B IS 48 NEWTON CALCULATE THE WEIGHT OF A,…

A:

Q: Consider a Carnot vapor refrigeration cycle with Refrigerant 134a as the working fluid. The cycle…

A: Given:Cold region temperature, TC=40oFThe ambinet temperature, TH=90oFFind:Coefficient of…

Q: 3. In the figure below two equal forces are applied to the tap wrench a distance d from the center…

A:

Q: Answer D

A:

Q: As shown in figure 3, water (kinematic viscosity of water v =10 m's) flows out of a reservoir into a…

A:

Q: Determine the position of the neutral axis of a curved bar subjected to flexure by a couple shown in…

A: The position of the neutral axis of a curved bar subjected to flexure by a pair must be…

Q: Instructions: Identify the talking components by choosing the most appropriate answer from the…

A: To determine: I directly determine what the speed of a hydraulic actuator is going to be. What am…

Q: 15 kN 20 kN 2 m m

A:

Q: Conversion of units: A pyramid has a height of 500 ft, and its base covers an area of 15.0 acres…

A:

Q: In (Figure 1), the man has a mass of 75 kg and the crate has a mass of 130 kg. The coefficient of…

A:

Q: Determine P and RA

A:

Q: A plane's propeller can be modeled as a thin, uniform rod that rotates about its frictionless center…

A: Given data  F = 591 N  L = 6.51  m  mass of propeller (m) = 10.1 kg    To determine  (a) direction…

Q: A vacuum gauge mounted on a condenser reads 66 cm Hg. What is the absolute pressure in the condenser…

A:

Q: Your professor at HTU asked you to explain Archimedes topic to your classmates at one of the classes…

A:

Q: A 1000 kg automobile accelerates from 10 km/hr to 120 km/hr. How much work does this require?

A: Question(4)Given:Mass  Initial Velocity Final Velocity To find:The required Work

Q: 1. Find the tangential velocity (VA)o 2. Construct diagrams to show, the rotational motion…

A: for solution refer below images.

Q: 4/29 Determine the force in member CG. Ans. CG 14.14 kips T H 10 G 10 F 10 E 10 A B D 5 kips 5 kips…

A: Force in Member CG is 14.14 kips [Tension].

Q: 1. on-off: 2-way/pressurize-exhaust: 2. pneumatic valve: sub-base mounting/hydraulic valve: 3. hand…

A: Here in this question we have to complete the suggested relationship by choosing the appropriate…

Q: Situation #5: The body rotates according to the relation a = 4t, where a is in rads/s and t in sec.…

A: dw/dt = alpha it can be integrated to get the expression of angular velocity and this can be further…

Q: 3. A REVERSED CARNOT CYCLE IS USED FOR REFRIGERATION AND REJECTS 200 000 Btu/min OF HEAT AT 152.6F…

A: GIVEN DATA- Q2=200000 Btu/min TH=152.6'F TL=450.6'R WE HAVE TO FIND COP , CAPACITY , WORK

Q: A compression ignition engine has an inlet temperature and pressure of 15°C and 1bar respectively.…

A:

Q: Mechatronics Write the Boolean Expression for each of the following Figures: 1. 2. Page | 2

A: 1) A*B, since it is a AND gate

Q: 76. The air inlet mass flow rate mi can be determined from a. pilAV]I b. [AV]1/vI both of the above.…

A: P1=14.7psi T1=80 F V=1000 cfm P2=100psi T2=400 F

Q: 4/4 Calculate the forces in members BE and BD of the loaded truss. B

A: To calculate the forces in the member BE and BD.

Q: Instructions: In this exercise, incomplete relationships are set up among fluid conductors and…

A: Here, we have to complete the relationship among fluid conductors and connectors by choosing…

Q: 5. The semicircular gate is hinged at point A. What is the necessary force P needed to hold the gate…

A: The required force P. Given: The radius of the gate is R=15-8=7 ft. FBD: The free-body diagram of…

Q: designer of a ski resort

A: detailed Answer given below

Q: A centrifuge bowl is to separate two immiscible liquids, one with SG 1.1 and the other with SG 0.9.…

A:

Strain energy

The term strain indicates the variation in an object's length, area, and volume when the object is subjected to an external force. The external force may be of normal, shear, moment, torque, etc. The strain in an object depends on the types of external force and cross-section of the object. Mathematically, the evaluation of strain can be obtained with the help of elastic constants.