Calculate the total length, L( m), so that the resulting stress q is uniform. А. 10 В. 12 С. 9 D. 8 Which of the following gives the location (m) of the maximum shear from the left end? A. 4.0 В. 5.0 C. 6.0 D. 4.5 Which of the following gives the location (m) of the point of inflection from the left end? А. 1.24 В. 5.16 С. 6.28 D. 3.20

Calculate the total length, L( m), so that the resulting stress q is uniform. А. 10 В. 12 С. 9 D. 8 Which of the following gives the location (m) of the maximum shear from the left end? A. 4.0 В. 5.0 C. 6.0 D. 4.5 Which of the following gives the location (m) of the point of inflection from the left end? А. 1.24 В. 5.16 С. 6.28 D. 3.20

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maximum vertical force P that can be applied to the bell crank so that the average normal stress developed in the 10mm diameter rod CD, and the average shear stress developed in the 6mm diameter double sheared pin B does not exceed 175MPa and 75MPa, respectively. 45° 300 mm B -450 mm
1. Knowing that the: SET A TORQUE MAGNITUDE 9 kip.in 1.35 kN.m INTERNAL DIAMETER 0.9 inch B 12 mm 2 inches 3,000 lb.in determine the maximum shearing stress caused by the torque applied.
A force of 3000N is acting on the orange plank which is attached to the pin as shown in thefigure. a.) If the thickness of the orange plank is 75mm and the pin has a diameter of 20mm,compute the bearing stress acting between the plank and pin. b.) Compute theshearing stress acting on the pin and c.) the normal stress of the orange plank if it hasa width of 500mm.
1-61 The uniform beam is supported by two rods AB and CD that have cross-sectional areas of 12 mm² and 8 mm², respectively. If d = 1 m, determine the average normal stress in each rod. 1-62 The uniform beam is supported by two rods AB and CD that have cross-sectional areas of 12 mm² and 8 mm², respectively. Determine the position d of the 6-kN load so that the average normal stress in each rod is the same. B A 6 kN 3m D
The structure supports a distributed load of w. The limiting stress in rod (1) is 320 MPa, and the limiting stress in each pin is 160 MPa. If the minimum factor of safety for the 2.30 m 28-mm-diam. pin structure is 2.40, determine the maximum distributed load double shear B magnitude w that may be applied to the structure plus the stresses in the rod and pins at the maximum w. 24-mm-diam, rod 16-mm-dianm, rod 5.90 m (1) single shear 26-mm-diam. pin w 7426.08 kN/mX 6.80 m Thy One 01 133.33 MPAX TB 271.142 MPAX 78.837 MPAX
on 2 If we know that the tensile force in the 20-mm-diameter tie rod BC is 10 kN, what is the average shear stress (in MPa) in the 10-mm-diameter pin at B. ered ed out of ng question B 30 7000 N 3 m
Determine the maximum shear stress in the T-beam at section C. 10 kN/m Lisa- -15m- -15 m- 150 mm 是 150 mm 30 inm T-30 mm
A stepped shaft has the appearance shown in Fig. 5-13. The region AB is aluminum, having G= 28 GPa, and the region BC is steel, having G = 84 GPa. The aluminum portion is of solid circular cross section 45 mm in diameter, and the steel region is circular with 60-mm outside diameter and 30-mm inside diameter. Determine the maximum shearing stress in the aluminium in MPa if a torsional load of 4000 N-m is applied at B. Ends A %3D and Care rigidly clamped. 45 mm B 60 mm 30 mm 2m 1.2 m
Prob 3. (A) Draw shear diagram and determine the maximum shear force (V). (B) Determine the maximum shear stress in the beam at the point where the internal shear force is maximum. (C) Draw the shear stress (T) distribution over the entire depth of the beam. 30 40 kN/m TTTTTH 6 m 20 kN/m + 6 m B 300 30 ↑ 165 -40 dims. =mm
The horizontal shaft with a diameter of d = 44 mm is supported by a thrust collar that rests on a 37-mm-thick plate. The thrust collar is 29-mm thick. The thrust collar has an outer diameter of Dcollar = 69 mm. Determine the load P that causes an average shear stress of 69 MPa on the cylindrical surface of contact between the shaft and the thrust collar P Thrust collar Answer: d A = i Plate Determine the contact area between the shaft and the thrust collar. Thrust collar area mm² d Dcollar
Q3. Draw the shear and bending for the following: 75 kN 90 kN 80 kN-m 100 kN-m • A 6 m -2 m--2 m- 75 kN 201 10 ft A B ,,,,,,,,+*རྐ་ 0.5k/ft 25 ft
почин Two horizontal 7.5-kip forces (P) are applied to pin B of the assembly shown. A 0.8-in. diameter pin is used at each connection. 0.5 in. 18 in 18 in P 0.5 in. 45% 18 in. 60 Determine the maximum value of the average normal stress in link AB. The maximum value of the average normal stress in link AB is 60 Two horizontal 7.5-kip forces (P) are applied to pin B of the assembly shown. A 0.8-in. diameter pin is used at each connection. 0.5 in. P 0.5 in. ksi. 18 in. Determine the maximum value of the normal average stress at the midpoint of link BC. The maximum value of the normal average stress at the midpoint of link BC is ksi.