The 60-mm-diameter solid shaft is subjected to the distributed and concentrated torsional loadings shown. - Determine the absolute maximum and minimum shear stresses on the outer surface of the shaft and specify their locations, measured from the fixed end A - Change the diameter of AB and BC from 60mm to 68.97 mm - change the applied external torque at point C of 1200 N-m to 1440 N.m - determine the angle of twist of point C (relate to point A). Assume that the shaft is made from Red Brass C83400. - plot the internal torque across the entire length of the shaft.

The 60-mm-diameter solid shaft is subjected to the distributed and concentrated torsional loadings shown. - Determine the absolute maximum and minimum shear stresses on the outer surface of the shaft and specify their locations, measured from the fixed end A - Change the diameter of AB and BC from 60mm to 68.97 mm - change the applied external torque at point C of 1200 N-m to 1440 N.m - determine the angle of twist of point C (relate to point A). Assume that the shaft is made from Red Brass C83400. - plot the internal torque across the entire length of the shaft.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid brass shaft with an allowable shear stress of 51 MPa. Segment (2) is a solid aluminum shaft with an allowable shear stress of 78 MPa. If a torque of Tc = 25700 N-m is applied at C, determine the minimum required diameter of the brass shaft d₁ and the aluminum shaft d2. Tc Answers: d₁ = i √₂ = i (2) с B A mm mm
,,
A solid 1.750-in.-diameter steel shaft is subjected to torques TB = 285 lb-ft and TD= 115 lb-ft, acting in the directions shown. If the allowable shear stress in the shaft is 22 ksi, determine the maximum torque TC that can be applied to the shaft.
Several torques are applied to the stepped shaft (G= 80 GPa) shown in Fig. 1. Neglect any Stress concentrations associated with the sudden change in cross-section. Determine: (a) The maximum shear stress in the shaft (b) The rotation of the end E relative to the end A. 500 N-m 300 N-m FC 30 mm 400 mm A C 150 N-m 300 mm 350 mm D 50 N-m E 450 mm 20 mm
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torqueT that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel. 75 mm 50 mm A Bronze B Steel
Several torques are applied to the stepped shaft (G= 80 GPa) shown in Fig. 1. Neglect any Stress concentrations associated with the sudden change in cross-section. Determine: (a) The maximum shear stress in the shaft (b) The rotation of the end E relative to the end A. 500 N-m 300 N-m FC 30 mm 400 mm A C 150 N-m 300 mm 350 mm D 50 N-m E 450 mm 20 mm
The right angle bar is supported by a pin at B and a roller at C as shown in figure. The 30 mm diameter pin is in double shear. The shear stress in the pin is limited to 120 MPa. Neglect torsional effect. 400 mm BC The maximum safe value of Pis 30° P 480 mm kN. (Round off to one decimal place)
25. Design stress is less than the ultimate strength. O 26. If the internal bending moment is negative, the beam bends concave upward. O True False O O True False 27. If the internal shear is negative, the beam bends concave downward, True False
A solid circular bronze [G = 6,500 ksi] shaft, 6.0 ft long and 1.325 in. in diameter, carries a torque of 90 Ib-ft. For this shaft, determine: (a) the maximum shear stress in the shaft. (b) the magnitude of the angle of twist. Answer: (a) Tmax = psi (b) Ф%3D
The shaft AB is formed by bonding steel tube and a brass core. Outer diameter of the steel tube is 60 mm and the diameter of the brass core is 30 mm. The shaft is subjected to uniform distributed torque o t kNm/m. The allowable shear stresses for steel and brass are (Tsteel)all = 80 MPa and (Tbrass)all = 50 MPa, respectively. Determine a) the maximum value of the uniform torque t , b) the corresponding angle of twist at A. (The shear modulus for steel and brass are Gsteel = 77 GPa and Gbrass = 40 GPa, respectively) - Steel Tube A t kNm/m B 30 mm 15 mm 1 m 1 m Brass Core Cross Section
Determine the shear stress in pin A (double shear) and the normal stress in DE. The diameter of pin A is 0.125" and the cross section of DE is 0.15"x0.25". -2 ft -2 ft C A E 3 ft 600 lb