Calculate the safety of the cylinder pivot pin in relation to the yield. The tensile yield strength of the pin material is ReL=600MPa. The dimensions of the structure are: x1 = 10 mm x2 = 120 mm y1 = 110 mm y2 = 798 mm Piston rod = φ32mm Cylinder pivot pin = φ25mm Pliers pivot pin = φ30mm The clamping force of the pliers is 6000N Answer to one decimal place !!

Calculate the safety of the cylinder pivot pin in relation to the yield. The tensile yield strength of the pin material is ReL=600MPa. The dimensions of the structure are: x1 = 10 mm x2 = 120 mm y1 = 110 mm y2 = 798 mm Piston rod = φ32mm Cylinder pivot pin = φ25mm Pliers pivot pin = φ30mm The clamping force of the pliers is 6000N Answer to one decimal place !!

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5. A toggle device is used to compact scrap steel as shown below. If a Safety Factor of 3.5 is desired, and all the connections are pinned, design the 2 links of the toggle to have a circular cross-section and to be made from steel with Sy = 151 ksi and E = 30000 ksi. The force required to crush the shavings is 5000 lb. -Shavings Crushing force = 5000 lb 60 in- 15° 12 Toggle links- Applied force 60 in D = ? Section A-A Length typical both links
The shaft is pulled by force F. Shaft The yield strength of the material is 500 MPa and the factor of safety is 2 Spindle length 1 m Size the shaft as the outer diameter / inner diameter ratio is 1.5 Note:show the calculations in detail
Asap
EHide blocks The bar shown in the following figure has a diameter of 40 mm and is subjected to a force P = 1500 N and a force F= 500 N. It is made from a material which has a yield strength of 60 MPa. Determine the factor of safety at points A and B using the Von-Mises Theory. 100 mm 150 mm F B. P
The 24-mm-diameter A-36 steel rod is subjected to the axial forces shown. Take E = 200 GPa. (Figure 1) Figure 600 mm B 400 mm 50 kN 50 kN C 40 kN 1 of 1 > ▾ Part A Determine the displacement of end C with respect to the fixed support at A. Express your answer to three significant figures and include the appropriate units. dc = Submit μA Value Provide Feedback Request Answer Units ? 4
The specifications for a coil spring are known. Infinite fatigue life is required, using a safety factor of 1.3 applied to the maximum load only. The fatigue strength can be represented by a line between τmax= 600, τmin= 0 and τmax= τmin= 900 MPa.Assume both end plates are in contact with nearly a full turn of wireand that the end plate loads coincide with the spring axis.Determine a suitable combination of d, D, and N, if C = 8
Consider the steel truss and member cross-section presented in figures below. All the members of the truss have the same cross-section as shown in the figure to the right. They all also have a Young's Modulus of 210 GPa. What can the highest value of force F be before member AC fails by buckling? Force 1AN - 300 mm 40° 4 m $35 mm 7m 300 mm 8 m 35 mm 35 mm 35 mm Please provide your answer in kN.
The yoke and rod connection assembly shown in the figure below is subjected to a tensile force of 5 kN. I Determine the tensile stress in each rod. Determine the shear stress in pin A between the members. If each rod is 600 mm long, determine the overall extension of the assembly. Ignore any stretch in the joint. 40 mm 5 kN. 30 mm 25 mm 5 kN
A ductile bar as shown in figure 1 has a yiel strength of oy = 390 MPa. Force F makes a 30° angle with the positive x axis. Deter- mined the magnitude of F that will cause yielding. Hint: Select the most loaded point in the structure and the failure theory to use according to the material (The standard one for this type of material). Refer to the lecture. 2 y 7 75 mm 500 mm F 300 mm X
66 ll ? e V:09 The rod BD is made of material with G1= 135 GPa has a diameter 16 mm is bonded to the tube CA at point B, the tube made of material with G2=230 GPa has an outer diameter 37 mm and wall thickness of 7 mm. If T1=803 N.m and T2=1445 N.m, answer the following questions: B T2 N-m 0.4 m 0.1 m D. 0.3 m T1 N-m The polar moment of inertia of the rod BD is Your answer The polar moment of inertia of the tube CA is
The block is subjected to a force V = 48 kN. What is the resulting deflection Δ? Last answer was 2.11x10 -1 and it said the applied force causes a shear stress that is higher than the yield stress, so the response is not linear elastic.
Question 6 A B 112 mm 1.2 m 0.9 m Figure 6 The structure supports force P=75 kN, as shown in Figure 6. The solid circular rod BD is made of A992 steel: a. Find the vertical and horizontal component acting on the pin of the pulley C. b. Find the compressive force in the rod BD. c. Find the effective length-factor for BD. d. Express the radius of gyration about any centroidal axis for a solid circular area as a function of the diameter of a circle. e. Find the critical effective slender ratio (KL/r), according to the AISC specifications. f. Determine the required minimum diameter of the A992 steel solid circular rod BD to the nearest mm as allowed by the AISC specifications. g. Determine the F.S. for buckling of the designed rod DB. -0.9 m P