10.11. A delta rosette is placed on a steel plate and indicates the following strains:Ej = 400 µm/m€2 = 84 µm/m%3D€3 = -250 µm/mCalculate the principal strains and stresses, the maximum shear stress, and theorientation angle for the principal axes.

Given that: Strain gage rosette type is delta rosette. Measurements are: ε1=400 μm/m ε2=84 μm/m…

Answered: Calculate the principal strains and…

Calculate the principal strains and stresses, the maximum shear stress, and the orientation angle for the principal axes.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.15P: A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded...

See similar textbooks

Similar questions

10.4 A steel thick cylinder of external diameter 150 mm has two strain gauges fixed externally, one along the longitudinal axis and the other at right angles to read the hoop strain. The cylinder is subjected to an internal pressure of 75 MN/m² and this causes the following strains: (a) hoop gauge: 455 x 10-6 tensile. (b) longitudinal gauge: 124 x 10-6 tensile. Find the internal diameter of the cylinder assuming that Young's modulus for steel is 208 GN/m² and Poisson's ratio is 0.283. [96.7 mm]
10.4 (B). A steel thick cylinder of external diameter 150 mm has two strain gauges fixed externally, one along the longitudinal axis and the other at right angles to read the hoop strain. The cylinder is subjected to an internal pressure of 75 MN/m² and this causes the following strains: (a) hoop gauge: 455 x 10 tensile (b) longitudinal gauge: 124 x 10 tensile Find the internal diameter of the cylinder assuming that Young's modulus for steel is 208 GN/m² and Poisson's [B.P.] [96.7 mm] ratio is 0.283. 100
The structure shown in Fig. la is subjected to loading P and T. A set of strain rosette is positioned at point A for strain measurement. The orientation of the strain rosette is shown in Fig. 1b. The material properties are given as E = 200 GPa, G = 77 GPa and v = 0.3. If P = 10 kN and T= 250 Nm, find the following: i. The state of stress at point A and sketch the stress element. ii. The principal stress at point A and sketch the stress element. iii. The principal strain at point A and sketch the strain element. iv. The values of each strain gauge (Ea, Eb and ɛc). V. Name one change that can be done to lower the strain value at point A. 50mm 75mm 120 120° T Ø 50mm Ø35mm Fig. la Fig. 1b -----
If the engineering strain in a tensile bar is 0.0025 and Poisson’s ratio is 0.33, find the original length and the original diameter if the length and diameter under load are 2.333 ft. and 1.005 in. respectively.
Please make it easy to understand. Thank youu
A rectangular steel block is 300mm in the x direction, 200mm in the y direction and 150mm in the z direction. The block is subjected to a triaxial loading consisting of three uniformly distributed forces as follows: 250kN tension in the x direction, 320kN compression in the y direction and 180kN tension in the z direction. For steel, v=0.30 and E=200,000MPa. Determine the total strain in the x direction due to the forces applied in the three directions.
(d) Define Modulus of Resilience 2. Draw the stress-strain diagram for a typical ductile material and locate the salient points onit 3. A bar of 25 mm diameter is tested in tension. It is observed that when a load of 60 kN is applied, the measured over a gauge length of 200 mm is 0.12 mm and contraction in diameter is 0.0045 mm. Find Poissa 4. A circular rod of diameter 16 mm and 500 mm long is subjected to a tensile force 40 kN. The modulus of e steel may be taken as 200 kN/mm?. Find the elongation and strainin the bar due to applied load. 5. Define (a) Resilience (b) Proof resilience PART -B structions: Part B consists of 3 Units. Answer any one full question from each unit. Each questioncarries 8 marks and may have su 1. A steel circular bar has three segments as shown in the fig. Determine the total elongation ofthe bar. Take E = 210 GPa. 300 kNI 330 kN 30 mm 50KN 15 mm 20 mm 80 kN A + 150 mm 200 mm 250 mm B. D (OR)
None
Question 3: Please refer to the metal bar and its cross-section shown below. Two strain gages a and and b are attached to the bar as shown; note that 3 is the angle of their orientation with the x-axis. Assume: the Young's modulus of the metal = 16, 500 ksi; the Poisson's ratio of the metal = 0.33; P, = 13 kips; P, = 20 kips; d = 4.0 in.; t = 0.75 in.; L = 18 in.; and B = 40°. Determine the strains expected in the strain gages. 가 2 B b a H Ps N H y d
1. A 0.015 meter diameter bar of steel is stress tested and the following stress-strain curve is produced Stress (psix 10 60 50 8 20 10 1 MPa 300 100 psi (x 10%) 50 200-30 OL 40- 20- 10 0.05 0.005 1 L 0.010 0.10 Strain a. What is the ultimate tensile strength (MPa)? d. What is the yield strength(MPa)? 0.15 c. What is the percent plastic elongation at the time of fracture? e. What is the Modulus of Elasticity (GPa)? 400 300 200 Stress (MPa) b. What is the greatest load that can be place on this bar before failure(N)? 100 10 0.20
QUESTION 4: An originally rectangular rubber piece is deformed into the shape given by the dashed lines. Calculate, (a) The average normal strains along AC and BC. (b) The shear strain yxy at all corners. 4 mm 6 mm 3 mm 300 mm { 2 mn A 500 mm 4 mm
I need the answer as soon as possible