Calculate the aerosol scavenging coefficient Ʌ as a function of the diameter dp of the scavenged particle over a size range of 0.01-0.1 micrometer diameter for drops of diameter Dp= 5mm falling at their terminal velocity in air at 25 C. Assume that p0 = 1 mm h^-1

Q: Consider a suspension settling under hindered settling conditions (type III) in a cylinder with…

A: To find:(a) The hindered velocity of settling.(b) The Galileo number and The Richardson Zaki…

Q: Air at a pressure of 1/10 atm and 276 K flows with a free flow velocity of 700 m/s along a flat…

A: Given: The pressure of air, P1 = 1/10 = 10.1325 kPa The temperature of air, T1 = 276 K The air…

Q: 6. Diffusivity. the diffusivity of volatile solvents is frequently measured using an Arnold cell.…

A: Given: The length of vertical glass tube, L1 = 10 cm = 0.1 The surface area of glass, A = 1 cm2 The…

Q: Air at 100 Fahrenheit and 2 atm is being passed over a shallow bed of naphthalene spheres that are…

A: Given Data The temperature of the air is:T=100°F The pressure of the air is:P=2 atm The diameter of…

Q: A cylinder (20 mm in diameter and 100 mm long) is heated internally by an electrical heater and is…

A: Given; Cylinder diameter, D=20 mm=0.02 m Cylinder length, L=100 mm=0.1 m Air velocity, V=20 m/s Air…

Q: A chromatographer fed up with waiting 36 minutes to accomplish a separation requiring 8000 plates,…

A: A) PLATE HEIGHT will be major than on first conditions, on the off chance that you descrease the…

Q: A particle has a diameter of 0.20 millimeters (Spec.grav = 2.5) falling in a liquid (Spec.grav =…

A:

Q: 13-3. Apply the power curve of Fig. 13-14 to a site with average wind speed of U=7.7 m/s, with bin…

A:

Q: B- A continuous separating tank is to be designed to follow after a water washing plant for liquid…

A:

Q: The sliding plate viscometer shown below is used to mensture the viscosity of a fhuid. The top plate…

A: newton's law of viscosity will be used in this case

Q: KNOWN: Temperature and velocity of engine oil. Temperature and length of flat plate. FIND: (a)…

A: Step - 1:Tf​=2T∞​+Ts​​=2100+20​Tf​=60°CTf​=333KGiven…

Q: Calculate the Cunningham correction factor for a particle with a 0.03-micron diameter in air at 1…

A: Given, Size of particle, d=0.03μm Pressure at T=0°C is p=1atm p=760 torr Cunningham slip correction…

Q: Sintered silicon nitride parts are expected to experience tensile stresses 50% of the ultimate…

A: Given data:- tensile stresses (σ) =50% of the ultimate tensile strength Specific surface energy (γ)=…

Q: During the glass plate production process, blocks with a temperature of 1400°C are produced. These…

A: Given data: Temperature at the center of the glass block = T1 = 1400°C Temperature at the sides = T2…

Q: For the diffusion coefficient K = 0, the above equation becomes: If known: The flow velocity is…

A:

Q: the entire room once released, the droplets have a density of 1000 kg/m 3, and they do not…

A: Definition:Stokes' lawStokes' law is a mathematical equation that defines the drag force applied to…

Q: A cylindrical sample of a biological product (10. mm in diameter and 18 mm in height) was exposed to…

A: Calculate the change in force in the time when it decreases to 36% of the initial value.…

Q: Estimate the stopping distance (Xs) and the impaction number N1 for a droplet diameter of 1000…

A:

Heat Exchangers

Heat exchangers are the types of equipment that are primarily employed to transfer the thermal energy from one fluid to another, provided that one of the fluids should be at a higher thermal energy content than the other fluid.

Heat Exchanger

The heat exchanger is a combination of two words ''Heat'' and ''Exchanger''. It is a mechanical device that is used to exchange heat energy between two fluids.