Answered: Calculate for the shear force in kN at…

Calculate for the shear force in kN at member HG of the frame shown in figure 1 using Portal Method. Enter absolute value and use 2 decimal places in your solution.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: For the truss shown, Fi=240KN and F2=720KN. Determine the forces in the rod BD and the rod BE (unit…

A: Given: F1=240 kNF2=720 kN

Q: Analyze the howe truss with the given dead load as shown in the figure. Bottom chord dead load = 5kN…

A: Solution: Dead load = 5kN Because of the symmetric truss and load: A=Hy=12total load = 0.5 × 5 × 5…

Q: The cross-sectional dimensions of the beam shown in the figure are a = 4.1 in., b = 5.6 in., d = 5.0…

A: Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum…

Q: 6. A 100 N force acts along 10 points the line AB, as shown in the figure below. Determine the…

A: Consider the given figure Given data F=100 NL=20 mmB=20 mmL and B are length and breath of the…

Q: A beam has circular cross-section. Shear stress at a depth of 0.6R from x-x line as kV then kis TR²…

A: Given data,

Q: The bell crank is in equilibrium for the forces acting in rods (1) and (2). The bell crank is…

Q: 80k (7.5) 10 (7.5) (4) (4) 20 20 (3)

Q: Tension only members B 4m 5m 5m 20kN C 5m D

A: A truss is given as shown in the figure above and it has been asked in the question to determine the…

Q: Problem 1 (4:- O. For the given truss below, |2 k |2 k |2 k answer the questions. A = 1.5 in² and E…

Q: The strain in the x direction at point A on the A-36 structural-steel beam(in figure attacched) is…

A: Neutral axis: YNA=122=6 inMoment of inertia:I=6×12312=864 in4 stress: stressσ=E×strain in x…

Q: Find the north axis and the moment of the second area Find both the triangular axis and the moment…

A: The following is the given information. My = 240 N.m Mx = 380 N.m Thickness of bottom flange = 1…

Q: For the truss shown below, P = 9.2 kips, a = 8 ft, and b = 6 ft. Determine the force in member 3…

A: Given :- P = 9.2 kips a = 8 ft b = 6 ft To find :- force in member 3

Q: A В C D a E F G Н F

A: using method of sections sign convention tensile =+ compressive = -

Q: The solid shaft is fixed to the support at C and subjected to the torsional loadings shown.…

Q: Solve the internal forces on the given beams. (N, V, M) The cutting plane should pass through the…

A: For calculating the shear and bending moment for the given beam we have to calculate reaction on the…

Q: For the given state of stress, determine (a) the maximum principle stress (b) the maximum shearing…

Q: 1. The section shown in the figure fails in flexure. Determine the magnitude of the compressive…

A: Given Data: a = 8 in, b = 16 in, h = 28 in Dia of hole = 8 in f`c = 5 ksi and fy = 60 ksi To find :…

Q: Find the force in truss DE. T = 390 N, x = 1.8 m. (Note: if the force in the truss is in tension,…

A: Joint method is used to calculate tension or compression in members of a system on which some load…

Q: 150 kN 150 kN 60 kN · m 60 kN - m В E -2 m 2 m - 5 m-

A: let,RA=vertical reaction at support A in upward directionRE=vertical reaction at support E in upward…

Q: Determine the maximum bending moment magnitude for the beam shown below. Use a = 18 ft, b = 6 ft,…

A: Solution:- Bending moments at various sections: BMC=0BMB=-6×6×62 =-108 kip.ftBMA=-6×24×242+96×18 =0…

Q: Below is a truss created with 3 rod elements. Fixed at point A, sliding support at point C has. At…

A: Truss with 3 rod elements is: Cross section of rod: Elastic Modulus of rod E = 20 GPa Factor of…

Q: The following beam is subjected to bending. Consider cross-section K! IF K + 1/2 + 1/2 + y. + A a +…

A: F = 15 kN l = 2.4 m a = 80 m v = 5 mm e = 2.23 cm I1 = 77.65 cm4 I2 = 18.178 cm4

Q: 1. For the assembly shown, determine the displacement of point B and D as the load of 50KN is…

Q: A symmetrical beam cross section is shown below. The centroid is in the exact centre of the section.…

Q: Solve the internal forces on the given beams. (N, V, M) The cutting plane should pass through the…

A: For calculating the shear force on both sides first calculate the reaction on both supports. In the…

Q: The

A: LAB=10/cos40°=13.05 ft LAD=10/cos20∘=10.64 ft ΣFV=0PABcos40∘+PAC+PADcos20∘=10(1000)…

Q: a. Axial force on member ED from the real structure in kN. Put (-) negative sign if it's under…

A: Given Data: A truss of A=1200 mm2, E=200 Gpa α=12*106 /°C It is asked to find axial force in…

Q: a force q of magnitude 3kips is applied to machine element AB. the uniform thickness of the element…

A: The given figure is shown below:

Q: For the beam shown a. Determine the maximum flexural stress b. If the nails shown in the…

Q: Solve the internal forces on the given beams. (N, V, M) The cutting plane should pass through the…

Q: The midpoint B of the steel cantilever beam ABC is supported by a vertical aluminium ro maximum…

A: Draw the free body diagram

Q: Determine the load P that can be

Q: Analyse the force in member BD of the truss in Figure Q2 by using the Force Method analysis. AE is…

Q: rces in members BC and CG. The

Q: Solve the forces in the following system, and determine the area of each bar such that the stress in…

Q: 1. Macts in a vertical plane. Find bending stress 30 50 30 M= 20KN- m 30 5 pt 30 Dimension in mm at…

Q: SOLVE THE PROBLEM USING DOUBLE INTEGRATION METHOD Problem II. The midpoint B of the steel cantilever…

Q: Problem II. The midpoint B of the steel cantilever beam ABC is - Aluminum supported by a vertical…

A: A cantilever beam is a direct member of a building or structure which is rigid from one end and free…

Q: 3. The shaft is attached to rigid fixed supports at each end. The maximum shear stress will be equal…

Question

Calculate for the shear force in kN at member HG of the frame shown in figure 1 using Portal Method. Enter absolute value and use 2 decimal places in your solution.

a = 22.7 kN, b = 46.1 kN, c = 2.5 m, d = 5.1 m, e = 3.5 m
a kN
C
F
I
b kN
B
em
E
em
H
em
K
cm
dm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Analyze the howe truss with the given dead load as shown in the figure. a. Find the length of all members of the truss. b. Find the stress (in kN) of all members and determine if its compression or tension. C. Find the Rav and Rgv Please answer with complete solution.
complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101 SN = 94 Determine the reactions and forces (internal loadings) for points A, B, C, D and E as shown in the figure below.
Solve please
The shaft is made from a solid steel section AB and a tubular portion made of steel and having a brass core. If it is fixed to a rigid support at A, and a torque of T = 50 lb.ft is applied to it at C, determine the rotation angle that occurs at C relative to A and compute the maximum shear stress and maximum shear strain in the brass and steel. Take Gst = 11500 ksi, Gbr = 5600 Ksi. 3 ft 2 ft 0.5 in. B 1 in. T = 50 lb·ft
25. Design stress is less than the ultimate strength. O 26. If the internal bending moment is negative, the beam bends concave upward. O True False O O True False 27. If the internal shear is negative, the beam bends concave downward, True False
I want the correct solution with proper explanation.
The horizontal beam is supported by a pin at A and the pin-connected link BC. It has a uniformly distributed loading w = 2.6 kN/m as shown in the figure. All the pins are in double shear and have a diameter of 20 mm. Determine the max shear stress in the pin at C. Input your answer as a value only in MPa to one decimal place without +/- sign. W 1.5 m 2 m B 1m
A pin-jointed truss ABC shown below consists of two links AB and BC. These links are 6 mm thick and 20 mm wide as shown. There are support brackets at A and C. All pins are 12 mm in diameter and a vertical force, P = 9 kN is applied at pin B as shown. The angle 0 =38 deg. and the angle ẞ = 0 + 20 deg. The normal stress in link AB is (The result is accurate to one decimal place, in the unit MPa. Please write down only the value of your final result) · 12mm 9 20mm -1.0m⋅ B
1. A stepped shaft is shown, the region AB is aluminum having G = 28 GPa, and the region BC is steel, having G= 80 GPa. The aluminum portion is of solid circular cross section 45 mm diameter, and the steel region is circular with 60 mm outside diameter and 30 mm inside diameter. A clockwise torsional load of 4000 N-m is applied at B, assume ends A and Care rigidly clamped. De termine the following: a. maximum shearing stress in the aluminum b. maximum she aring stress in the steel (
For the truss shown and loading, determine the axial stress in member BH in ksi. Use two decimal places. Express your answer in absolute value. Assume the sectional areas of the following: Top and bottom members = 1.80 in² Web members = 0.90 in² B 20 kip с 40 kip 6 ft @ 4 = 24 ft D 6 ft
Please answer carefully, do not copy. It's all wrong online.