For the beam shown a. Determine the maximum flexural stress b. If the nails shown in the cross-section can each support a shear force of 600 N, determine their required spacing along the beam. P=10kN Wo=8kN/m a=10m

Q: A pulley is supported by a circular pin at A. The pin has a diameter of d= 0.625 in., and each side…

A: - Horizontal axis = 0- Vertical axis = 0- Resultant force on pin is given by PR ;

Q: Two vertical forces are applied to a beam of the cross-section shown. Determine the maximum…

A: Given Data: a = 7.5 m b = 4.2 m

Q: QUESTION 2. An oblique bending moment of M = 5 kN.m is applied on the cross-section of an aluminum…

A: Solm ⇒ * Nevtral axis orientation* A1=10×40 ⇒ 400 mm2 , x1=402 ⇒ 2c mm, y1 = 5 mm  A2 = 50×10 ⇒ 500…

Q: Use the virtual work method to determine the deformation at joint B of the truss shown. 3 m A -2 m-…

A:

Q: The strain in the x direction at point A on the A-36 structural-steel beam is measured and found to…

A: Given:- The strain in the x-direction at point A = εx = 217 x 106  A point load P is applied at…

Q: 3: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that…

A: Given data  dAB = 1.25 in  dBC = 0.75 in  P = 10 kips

Q: The members of the truss shown have identical cross- 3P sectional area of 200 mm². Determine the…

A: Allowable stress = 40 MPa = 40 N/mm2 Allowable axial displacement = 0.1 mm  E = 70 GPa = 70 × 103…

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional…

A: Given data- Cross sectional area of Truss member = 3.6 in2 Maximum normal stress in each member = 50…

Q: Q.2) A rigid bar ACD is supported by two circular steel (E= 30x10° psi) rods DE and a pin support at…

A: Draw free body diagram From deflected shape δAB8=δP4=δDE6=tanθ Consider the moment equilibrium…

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

A:

Q: The rigid bar AB of negligible weight is supported by a pin at O. When the two steel rods are…

A: Given data,  E for steel = 200 Gpa Cross section area of AC = 300 mm² Cross section area of BD = 250…

Q: The bars of the truss each have a cross-sectional area of 1.68 in2. Determine the average normal…

A:

Q: Prob 1. Determine the smallest diameter rod that will safely support the loading shown. The…

A:

Q: Determine the shear stress at points: A, B. C, D and E in beam shown in Figure 5. Take E-30 GPa

A: Shear force at section 1-1: V11=-30×2=-60 KN     Moment of Inertia (I): I=0.2×0.5312=2.0833×10-3…

Q: Cm 4m 4m Gom G Gm. F Gm 76 KN 14 76 KN

A:

Q: Question 2: Two-pinned connected bars supported the rigid member BC as shown. A vertical load of 25…

A: Stresses in both the bar is same.Determine the distance x.

Q: A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as…

A: Hi! Thank you for the question. As per the honor code, we’ll answer the first question since the…

Q: The bars of the truss each have a cross-sectional area of 1.92 in². Determine the average normal…

A: Step 1:- force in member BD using method of joint or method of section. Step 2:- Normal stress =…

Q: Rigid bar ABCD is loaded and supported as shown. Steel [E = 28400 ksi] bars (1) and (2) are…

A:

Q: Determine the maximum tensile bending stresses in the beam shown. LetP= %3D 19 Note Answer in whole…

A: bending stress=MmaxIyt I= 100× 106 mm4 Yt= 200mm Mmax=6P =6×19=114 kNm( hogging) Hence will cause…

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional…

A:

Q: The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter…

A:

Q: Problem 2. [Concepts: Internal forces in 2D and average normal stress] The bars of the tru each have…

A: Cross sectional area (A) = 1.25 in.2 a. Determine the average normal stress in each member if P = 8…

Q: The frame supports the distributed load shown. Determine the state of stress acting at point E. Show…

A: Draw the free body diagram.

Q: 4. Steel plate (2) b. Consider a point in a structural member that is subjected to plane stress.…

A: A stress element is given.Take normal compressive stress as (-)ive and tensile stress as…

Q: For the truss shown and loading, determine the axial stress in member BH in ksi. Use two decimal…

A:

Q: can you please show how to find the elastic stress and design ratio?

A: The figure given in the question is as follows Total depth of beam(D)=600 mm Width of beam(b)=300…

Q: When an axial load is applied to the ends of the bar shown in the figure, the total elongation of…

A: