Please solve asap a..DATA.CODEVAL1 DW 19A7HVAL2 DW 20C8HVAL3 DW 1005HREST DW 2 DUP (?)MAIN PROC FARMOV AX, @DATAMOV DS, AXPUSH VAL3PUSH VAL2PUSH VAL1CALL SUBR1MOV RESL, AXMOV REST +2, BXMOV AH, 4CHINT 21HMAIN ENDPEND MAINSUBR1 PROC FARSUB BX, BXPUSH BPMOV BP, SPMOV AX, [BP+6]MOV CX, [BP +8]MOV DX, [BP +10]ADD AX,CXADC BX, 00ADD AX, DXADC BX, 00POP BPRET 6SUBR1 ENDPENDAssume SP = 16C7H before the "PUSH VAL3" instruction in the mainprocedure. After the main procedure is executed, find the following:RESI =SP=b. User wants to add 128k EPROMs and 128k SRAMs to a PC using the 74138sto decode the 32k x8 memory blocks (EPROMs and SRAMS) controlled by Ys.Addresses available start 50000H and another D0000.1. How many memory block required from EPROMs and SRAMS?2. Determine the typical range address of added EPROMs and SRAMs?3. Determine the range of each memory block controlled by Ys?4. Design and draw the memory decoding using 74138 circuitries in which thememory block controlled by Ys?

Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

b. User wants to add 128k EPROMs and 128k SRAMs to a PC using the 74138 to decode the 32k x8 memory blocks (EPROMs and SRAMS) controlled by Y Addresses available start 50000H and another D0000. 1. How many memory block required from EPROMs and SRAMS? 2. Determine the typical range address of added EPROMs and SRAMs? 3. Determine the range of each memory block controlled by Ys?

b. User wants to add 128k EPROMs and 128k SRAMs to a PC using the 74138 to decode the 32k x8 memory blocks (EPROMs and SRAMS) controlled by Y Addresses available start 50000H and another D0000. 1. How many memory block required from EPROMs and SRAMS? 2. Determine the typical range address of added EPROMs and SRAMs? 3. Determine the range of each memory block controlled by Ys?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

* ELECTRICAL MACHINE.p... John G. Webster-Medic... Lecture_1_-_Basic_conce... Find: 31 Calling 5 Ag 10000 Linear potentiometer to measure the arc configuration in hospital beds monitor backrest elevation which helps ensure the proper angle is maintained for patients. Lecture 1- Basic conce... X Lecture 2 Amplifiers a... Lecture 2 - Amplifiers a... X SOLUTIONS.pdf ■ A 5 V excitation source Length of the potentiometer, 5 cm. ■ The measurement system used to test 31 200000 the arc configuration has input 00-520-2 impedance, R₁ = 1k. Dr. A.O. Vweza o Dpt. of Electrical Engineering Introduction V=+5V 5000 5002 Distribution of errors on repeated measurom RL El Mesurement system W 11.15 20 Ls. Assuming that the wiper is in the middle of the potentiometer whose value is 1000 2. What is the sensitivity of the potentiometer 2009 BBME 3, Bioinstrumentation, ELE-BII-311 9 system? What is the error in the measurement of voltage caused due to low value of input impedance? 514 muu DAWAT 1806 IkQ are…
Question2: There is no energy stored in the circuit in Figure at the time the switch is opened. M Ro -L2 iz ig a) Derive the differential equation that govens the behavior of i2 if L1 = 4 H, L2= 16 H, M= 2 H, and R0= 32 H. b) Show that when ig = 8 - 8et A, tz 0, the differential equation derived in (a) is satisfied when i2 = et – e2t A, t2 0. c) Find the expression for the voltage vl across the current source. d) What is the initial value of vl .Does this make sense in terms of known circuit behavior?
M:38)
i need help please
Please answer all subpart either dislike is ready Please answer I will like it please..
Hello Sir.Good Night. I have a question in my home work related Control System Lesson. The following below is my question.Please advise, Thank you so much.
Help me answer, I want to check my solution To get the contribution of the 75V source to iR, we first kill the 50mA source. What is the resulting equivalent resistance in series with the 75K resistor (in Kohms) To get the contribution of the 75V source to iR, we first kill the 50mA source. What is the resulting value of iR (in mA)? What is the nodal equation for Vx? What is the Thevanin voltage in (Volts) and Thevanin resistance in (Kohms)?
Plz fast
Use Voltage and/or Current Division to find an expression for 14. + V1 R1 R3 14 Vs R2 V2 R4 CS Scanned with Camscarner
Please solve a, b , c, d i will submit The rest again thank you
Do it on priority
I need an expert solution in MATLAB language for the question, and I need the solution to be using MATLAB and in the form of an image. I do not need any notes with the program, just an explanation at the end of the image. By the way, two questions. Q2. Write a MATLAB user-defined function, freefall(), that computes the velocity and the distance of a free fall object. The velocity and the distance of a free fall object can be written as: v = gt y = yo+gt² where yo is the initial position, t is the time travelled and g is the acceleration due to gravity (- 9.81 m/s2). Note that the initial position can only be a scalar value. Q7. Write a user-defined MATLAB Function for the following math function: ((xy-5)² z = if x, y > 0 elsewhere The inputs to the function are x and y, where the output is z. Write the function such that x and y can be vectors. I. II. Use the function to calculate z(3,4) and z(5, -7). Use the function to make a colored 3D plot of the function z for -5