3.61 In the circuit shown in the image below, if R1 determine the ratio i, /is. = 52 Q and R2 = 62 Q, R1 R2 is 75 2 9vo 90 2 Please pay attention: the numbers may change since they are randomized. Your answer should keep 3 places after the decimal point.

Q: What color fluorescent lamps recommended for residential installation

A: White color fluorescent lamps recommended for residential installation .

Q: 12. What is the primary entity that needs to be consulted with in regards to the location of the…

A: According to the electric code, The meter and the service box should be placed outdoor which can be…

Q: List the minimum trade size Type EMT for each of the following applications. (Objective 12-1)…

A: As per Bartleby expert policy only first individual question is to be answered. So, answering only…

Q: 9.a. What should be done with the connector ferrule once a connector is attached to a fiber optic…

A:

Q: What is the value of the resistor shown below in ohms? Don't use scientific notation. #1

A: Resistors can be used for both electrical and electronics circuits when current is passed voltage…

Q: Which of the following would be one of the first checks made by a technician when troubleshooting a…

A: Need to talk about troubleshooting of a small.residential condensing unit

Q: What are the three project categories an electrical contractor may choose to browse?

A: There are different projects in the world, and every project needs some specialty for completing it.…

Q: What is sub station

A: A power station is to provide electricity to a huge number of people. Different customer’s power…

Q: L-march or T-match matching box

A: An L-match or T-match is a type of impedance-matching network used in radio frequency (RF) circuits…

Q: Determine the size and type of wire to he installed to a building with temperature that reaches…

A: Here ratings of loads are given for a single phase 230 V source. We need to determine the size and…

Q: What are the different Impedance matching devices?

A:

Q: What can you say/perspective about National Electrical Code?

A: The National Electrical Code (NEC) was created to protect people and property from the risks posed…

Q: What is the acceptable minimum value of leakage current of HI-POT Test of electrical cables. Can you…

A: According to the question,what is the acceptable minimum value of leakage current of HI-POT Test of…

Q: 12.A. A connector is a _______ device used to connect a fiber to a source, detector, or another…

A: The solution is given below

Q: where is it most convenient to find a PKES system

A: We need to tell about PKES .

Q: ). Fid the lovp currents mi the nefrrk sham. 32 2 J2 22.

A: Given

Q: What is receptacle load ? Explain under 100 words...

A: The amount of load produced by a device inserted into a receptacle is referred to as a receptacle…

Q: You have: MCB, Energy Meter, RCCB, and Change over. There two sources of electricity: one from the…

A:

Q: The nominal output voltage of a certain regulator is 8 V. The output changes 214 mV when the input…

A: It is given that: nominal output voltagevo=8 V,change in output voltage∆vo=214 mV,Vi=25 V to 16 V

Q: For an N channel E MOSFET what is the value of Id when VGS(TH)=3 V and Vgs(on)=4 V and k=1.5 mA/V2…

A:

Q: HERE IS IT

A: Physical address can be expressed by the following formula:Physical Address = (Segment Address) x 10…

Q: Which is easier to use a bnc connector or sma connector

A: BNC are bigger and easier and faster to handle. SMA are quite a bit higher in frequency capability…

Q: Q6) Explain by drawing a block diagram of a power supply?

A: Draw the block diagram of the Regulated power supply.

Q: A pvc raceway has multiple circuits installed. The circuit sizes are 20 amp 60 amp and 100 am. A…

A: To determine the appropriate size of the equipment grounding conductor (EGC) for a PVC raceway…

Q: if you have (10) 10 OHM resistors and (5) OMR resistors in a series circuit what would the total…

A: Resistances are given as,

Q: A protective put can be used for risk management.   A. TRUE B. FALSE

A: ANSWER      TRUE          A protective put can be used for risk…

Q: How Rth connected with the load resistance, explain

A: RL will be  connected in series with  RTH  as shown in the example.

Q: On a short/long bond paper, draw a schematic circuit diagram following your house wiring with…

A: electrical wires are designed to bear consistent electric current which should not lead to a fire in…

Q: 3. What must be the speed of a six-pole 25-Hz synchronous generator? 500 грm a) b) 900 гpm c) 1200…

A: NOTE: “Since you have asked multiple question, we will solve the first question for you. If you want…

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.