A thermistor is being used to measure temperature. For a given resistance R the temperatureis given byT =R1Indegrees KelvinIf To = 298 °K, B= 4000 and Ro = 20k2, calculate the temperature when resistance R is 15k2.At this temperature, determine the rate of change of temperature dT/dR in °C/2.

For a resistance R, The temperature measured by the thermistor is given by the following equation,…

A thermistor is being used to measure temperature. For a given resistance R the temperature is given by 1 In I, B T = degrees Kelvin R If To = 298 °K, B= 4000 and Ro = 20k2, calculate the temperature when resistance Ris 15k2. At this temperature, determine the rate of change of temperature dT/dR in °C/2.

A thermistor is being used to measure temperature. For a given resistance R the temperature is given by 1 In I, B T = degrees Kelvin R If To = 298 °K, B= 4000 and Ro = 20k2, calculate the temperature when resistance Ris 15k2. At this temperature, determine the rate of change of temperature dT/dR in °C/2.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Which of the following is NOT a variable in voltametric methods? A. How the current is applied B. How the potential is applied C. The inclusion of convection D. All the above E. Type of working electrode
a. A sine voltage trace displayed on a screen is shown in figure2. The x axis is 1unit=50 ms and y axis, 1 unit=2 V; determine the frequency of the sine wave and plot the waveform if the same is applied to the input of a half wave rectifier. Figure2
Calculate the current flowing through the given circuit and the voltage value at the V0 ends. (Threshold voltage = 0.3V for Germanium diodes, Threshold voltage for silicon diodes = 0.6V)
1-In the circuit designed to measure the effective value of the sinusoidal voltage at the input, diodes are considered ideal. M deflection is a measuring element with rotating coil. Rm=2k İm=(10)^-4 A. A- Draw the waveform of the current flowing through M on a scale. Determine the resistance value of R1 so that the nominal voltage value of V-m is 100V. B-What should the tolerances of the resistors be so that the Vm class is at most 1.5? (resistors have the same tolerances). R1 u(t) R2 1R3 18k 20k R4 k: k2 10k
Current 420 ohm 30 V 1,(max) = 80 mA Voltage Vp-in 2.2 kohm Vp-out 0.6 V Zener Current Answer the following question according to the above. Remember Kirchhoff's laws when making your calculations in this question. According to the given graph, how many volts is the voltage value on it when this Zener diode is on a flat supply?
60 V D1 D2 2 kohm DA D3 -60 V Assume that an input signal is applied to the circuit given above, as shown in the figure next to it. Accordingly, answer the following questions. The diodes used are silicon diodes, their operating voltages are 0.7 volts, and can be omitted because their resistance is very small. Calculate V p-out( Vm ) for this circuit.
Using 2nd approximation for the circuit shown, assuming that the diode used is a silicon diode, determine the currents ID1, ID2 and current through R2. Finalize answers as follows: ID1= Ir2= ID2= R2 D1 3.3 kQ BAT1 D2 20 V R1 5.6 kn
Example A NTC thermistor has a resistance of 30 KN at 0°C and material temperature constant 3575 K. calculate the value of the thermistor resistance at 25°C. Given NTC- thermistor hus
You are an electrician working on an overhead crane. The crane uses a large electromagnet to pick up large metal pipes. The magnet must have a minimum of 200 VDC to operate properly. The crane has an AC source of 240 V. You are given four diodes that have a peak voltage rating of 400 V each. These diodes are to be used to form a bridge rectifier to convert the AC voltage into DC voltage. Is the voltage rating of the diodes sufficient? To the nearest volt, what will be the DC output voltage of the bridge rectifier?
If the positive cycle of the waveform for full wave bridge rectifier , Which of the diodes is working . ..... ...... 10:1 D1 120 V ms Output 60 Hz Puec) RL 220 N D2 1000 µF D1, D2 D3, D2 D4, D2 O D1, D4 not all above O D1, D3 elle
Find the equivelent resistance of the circuit below. (Rin)Conduction diodes' resistance is 0Insulating diodes' resistance is infinite.R1 = 10 ohm
Electric Current and Resistance. What is an Electric Battery? Define electric current and state what is meant by the term conventional current. Describe Ohms's Law and draw an example using an I-V cuvre.