B.5 m3 m30 mm20 mm20 mmThe assembly above includes pin-connected column AB. Suppose that an analysis ofcolumn AB shows that it has a yield stress of 200 MPa and a buckling stress of 80MPa.If the design must provide a factor of safety for yielding of 1.5 and a factor of safetyfor buckling of 2.0, which of the following is closest to the maximum allowabledistributed load w?O 64 kN/mO 40 kN/mO 50 kN/mO 32 kN/m

Answered: Image /qna-images/answer/99e57248-7ba4-4bb4-a898-a3b07d0f6e35.jpg

B. 5 m 3 m 30 mm -20 mm T20 mm The assembly above includes pin-connected column AB. Suppose that an analy column AB shows that it has a yield stress of 200 MPa and a buckling stress of MPa. If the design must provide a factor of safety for yielding of 1.5 and a factor of sa for buckling of 2.0, which of the following is closest to the maximum allowable distributed load w?

B. 5 m 3 m 30 mm -20 mm T20 mm The assembly above includes pin-connected column AB. Suppose that an analy column AB shows that it has a yield stress of 200 MPa and a buckling stress of MPa. If the design must provide a factor of safety for yielding of 1.5 and a factor of sa for buckling of 2.0, which of the following is closest to the maximum allowable distributed load w?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.4P: Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield...

See similar textbooks

Similar questions

Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in tension is 975 MPa, the yield stress in shear is 460 MPa, the factor of safety is 2,75, the modulus of elasticity is 210 GPa, Poissorfs ratio is 0.28, and the normal strain must not exceed 1190 x 10" . For part (b), assume that the tank thickness is 8 mm and the measured normal strain is 990 x 10~ .
Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
Q1/A curved link mechanism made from a round steel bar 1 KN is shown in Fig. below, The material for the link is plain carbon steel 30CS with an allowable yield strength of 400 MPa. Determine the factor of safety. I KN I KN 80 mm 20 mm
Two metal plates, are joined as show below. Using standard material values, complete the following: a. Select a suitable bolt diameter b. For a load P = 150 kN. Determine the minimum plate thicknesses Hex head Aluminium bolt P Brass Upper plate P 150 Linear dimensions in mm 35 + # 80 35 P Copper Lower plate Modified from Statics and Strength of Materials by Morrow and Kokernak
3 in 2. For the C-clamp shown in Fig.1 , a perpendicular force is applied (into the page) at the end of the handle 3.5" from the centerline of the clamp screw. The handle has a diameter D= 1/2" and is made of AISI 1035 CD steel with a yield strength S, = 67 kpsi. The clamp screw is a 5/8 in–18 UNF, with ACME threads. Knowing that the maximum stress in the handle will occur at the location where the handle protrudes from the screw housing, what value of applied screw torque will cause the handle to bend permanently when the clamp is fully closed? What clamp force corresponds to this? Assume that collar friction is negligible and that the coefficient of friction between the threads and the nut is 0.15. Fig. 1
Find the equivalent stresses at Points 1 and 2 of the element with given geometry and loading conditions according to the Maximum shear stress hypothesis and the Maximum strain energy hypothesis. Shaft diameter: 20 mm, Shaft Length 120 mm, F1 = 750N, F2 = 3000N, Mb = 2400 N.mm. Steel if St37 and Safety coefficient is 2 If taken, will this stick work safely under these operating conditions? (Yield of given steel Strength 225 Mpa, Tensile strength 370 Mpa)
5kN Question 6 A mild steel bar 20mm x 20 mm in cross section is to be subjected to tension. Using a factor of safety of 4 based on the yield stress, find the working stress that is allowable in the steel bar. Hence, work out the allowable load. Given yield stress of mild steel is 250MN/m2.