b- Mark the following statement with True or False: 1. The protection works are now designed in respect to the scour depth. 2. Bligh's creep coefficient "C" depends upon the bed material. 3. The flow through a culvert can an open channel flow exist only. 4. Any hydraulic structure should be checked and designed for surface flow and subsurface flow. 5. The depth before the jump is called the sequent depth and that after the jump is called the initial depth.

b- Mark the following statement with True or False: 1. The protection works are now designed in respect to the scour depth. 2. Bligh's creep coefficient "C" depends upon the bed material. 3. The flow through a culvert can an open channel flow exist only. 4. Any hydraulic structure should be checked and designed for surface flow and subsurface flow. 5. The depth before the jump is called the sequent depth and that after the jump is called the initial depth.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Civil.problme.
Q3: A rough pipe has a diameter 80 mm. the velocity at a point 30 mm from the wall is 30% more than the velocity at a point 10 mm from the pipe wall. Determine (a) the average roughness height, (b) Darcy - Weisbach friction factor (f).
A thick-walled pipeline with internal and external diameters of 600 mm and 1000 mm, respectively, is subjected to an internal pressure P,. The cylinder is made of steel where E = 200 GPa, a,„ki= 250 MPa and v = 0.3. Given that the safety factor is 2, what is the maximum allowable pressure P, according to:- a) Tresca criterion, and b) von Mises criterion. Subsequently, sketch the HOOP stress distribution in the wall thickness of the pipe and indicate the values of the stresses on the inner and outer surfaces for EACH OF THE CRITERION mentioned above.
- Once answered correctly will UPVOTE!!
Simple solution
Determine the discharge in a composite gutter section if Sx = 0.033, SL = 0.015, a = 0.066 m, W = 0.6 m, and T = 1.95 m. Assume that the Manning roughness factor (n) equals 0.015.
find a
Q2/ For the soil profile, find the: 1- Total pressure (o,). 2-Pore water pressure ou (u). 3- Effective pressure o, God leved GL Sody = 16 KN/m? Ysaturated = 20o KN/m? (materlend 3 m ŏ saturated = 22 k/m? O sataraded = 19 KN/w?
The elbow flow passage volume is 0.37 m3 between sections 1 and 2. The flow rate is 0.90 m3/s and the elbow inlet and outlet pressures are 200 kPa and 130 kPa. Consider the elbow weight is negligible. Calculate the horizontal and vertical anchoring forces to hold the elbow in place. my results were Frx = 132.8kPa Fry = 76.7kPa
Two sections, A and B, are 0.5 km apart along a 0.05 m diameter rough concrete pipe. A is 115 m higherthan B, the water temperature is 4 °C, and the pressure heads measured at A and B are 21.7 m and 76.1 m,respectively. Assume minor losses are negligible. Determine the flow rate through the pipe
The length of the levee perpendicular to the paper is 600 m; the sand on top and bottom have k1=750 ft/day and k2= 40 in/s respectively. The thickness of sands is equal, m = 670 m, n=575 ft, B = 8ft, C = 525 ft. Determine the amount of water flowing to the ditch in in3/min. (See picture below)
A mechanically cleaned bar rack screen is installed ahead of a velocity controlled grit chamber. The bars are 10 mm thick, and the openings are 20 mm wide. The flow through the screen is 0.75 m3/s, and the depth of flow is 1.45 m in the channel upstream of the bar rack. 1. Calculate the flow velocity through racks (m/s). 2. Calculate the water depth in the channel downstream of the bar rack (m).