Determine the point where the neutral axis intersects line AB. The point where the neutral axis intersects line AB is mm above point A.

Q: 3. Find the centroid of the area in first quadrant bounded by the curve y² =4ax and latus rectum. dx…

A:

Q: Q1/ Find the slope of the line : 3x + 4y = 12. x+3= the slope is y=- m=--

A: Given: The equation of line is, 3x+4y=12 The slope of the line is to be determined.

Q: AB and CB are tangents. If y 137.20 mm and ZABC 67.0°, find: a) 21 -y 21 b) x C

A: Step 1

Q: 2g +0.501 20/3 T=0.50 b. Calculate the moment of inertia about the centroidal x-axis -f inortin ahnt

A:

Q: Locate the centroid y̅ of the area.

A: Following is the given area: Following is the given equation of y,

Q: Express the force F shown  as a Cartesian vector.

A: Consider the free body diagram shown below. The given data is, Consider the triangle shown below.…

Q: Consider the line 6x-3y=4. What is the slope of a line parallel to this line? What is the slope of a…

A: Given:-  Equation of line is 6x - 3y = 4

Q: Q1: Find the polar coordinates of the Cartisian point P(-2,2)

A:

Q: Find and a unit vector that is perpendicular to both à = -3i+2j+ 4k B = 51-25 +2k ft.

A: Given data:- The unit vector of A and B:- A→=-3i^+2j^+4k^ ftB→=5i^-2j^+2k^ ft

Q: Find the largest and smallest angle changes with their directions at point A, as the unit…

A: total X direction displacement of linesfor aa=+430×10-6 for BB=-260×10-6×cos60=-130×10-6for…

Q: Determine the distance from the point (5, 3) to the line 4x - 2y = 10.

A:

Q: R=0.956 m 6.97 R= =0.956 %3D b+2/2d b=7.29-2.828d

A:

Q: Hexagonal prism of base side 30 mm height 80 mm is resting on one of its base edge on HP. Its axis…

A:

Q: 5 B) Find y" for the function y =x + Vx at p(1,3)

A:

Q: 1. For the graph represented by the drawing below, find e2 US V4 a. the degree of all the vertices…

A:

Q: (mm) = 201

A:

Q: Determine the moment of inertia of the stringer cross section about the horizontal  centroidal axis.

A:

Q: Find an equation for the line that passes through the points (-5, 3) and (1, 5).

A: Given 2 points  (-5,3) and (1,5)

Q: Construct the third projection of the prism and complete the other two projections of point A, B, C…

A: Given prism and asked to draw third projection of prism.

Q: 4. Express the force F as a vector in terms of the unit vectors i, j, and k. Determine the angles…

A: Given,

Q: Determine degree of static indeterminacy of truss

A: Given data : Number of member (m)=13 Number of Joint (J)=8 Support=Pinned and roller support Number…

Q: 3 A line passes through the point (-4, – 2) and has a slope of 2 Write an equation in…

A:

Q: . The projections of a line in VP and HP are 66 mm and 54 mm long respectively. End A is 12 mm in…

A: Given:- VP=66mm HP=54mm End A=12mm mid point of line=36mm in front of VP and 28mm above HP   To…

Q: Which is the radius of curvature of the function y3Dvx at x=2? *

A: Using formula

Q: The side AB of an equilateral field ABC with an area of 692.80 sq.m. has a magnetic bearing of…

A:

Q: Express the force as a Cartesian vector.

A: Consider the figure,

Q: The intersection of two sph always a circle. anhere

A: If two spheres have the same radius and intersect at a single point, their intersection will indeed…

Q: A shunt pipe placed horizontally is shown on the right. The average velocity of section 1 is V1 =…

A: V1 = 3.50 m/s D1 = 0.15 m, A1 = π4 x 0.152= 0.177 m2 D2 = 0.076 m, A2 =π4 x 0.0762=0.00454 m2  D3 =…

Q: Problem 2) : The given composite areas in a), b) and c) can be divided into multiple elementary…

A: The centroid of a body is the point at which the mass of the body is uniformly distributed. The…

Control Survey and Geodetic reductions

Control surveys or survey controls are used to establish reference points as a basis for various construction activities. Vertical and horizontal control points are to be established in a control survey to increase accuracy. After establishing the control points, all other types of surveys such as topographic, right-of-way, aerial mapping, construction layout, boundary surveys, and utility mapping can be worked upon so that control networks can be formed. The place from which the observations are made is called a survey station.