A shunt pipe placed horizontally is shown on the right. The average velocity of section 1 is V1 = 3.5 m/s and its water pressure is P1 = 140 kPa. Does not consider energy loss If it is lost, try to find the magnitude and direction of the external force required to fix the shunt.

A shunt pipe placed horizontally is shown on the right. The average velocity of section 1 is V1 = 3.5 m/s and its water pressure is P1 = 140 kPa. Does not consider energy loss If it is lost, try to find the magnitude and direction of the external force required to fix the shunt.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 3 feet -hinge AC Linseed Oil (SG = 0.938) Castor Oil 32 feet (SG = 0.96) 7 feet 1water B 77

Q: Q3/ Water flows through a pipe at 5 L/s, as shown in Fig. 12.5 kPa, 11.5 kPa, and 10.3 kPa are…

A: Given, P1 = 12.5 kPa P2 = 11.5 kPa P3 = 10.3 kPa Q = 5 L/s or 0.005 m3/s NOTE : As per guidelines,…

Q: Consider the gate shown in the figure. If the length of the gate is 5 meters, calculate: LS. r= 4m…

Q: The diameter of a pipe carrying water changes gradually from 150 mm at A to 450 mm at B. A is 5 m…

A: Given data, Diameter at A = 150 mm Diameter at B = 450 mm Pressure at A = 70 Kpa Pressure at B = 50…

Q: Three pipes 1, 2, and 3 are connected in parallel and a fourth pipe is connected at B. The…

Q: The hydrostatic force due to linseed oil F1. b. The hydrostatic force due to castor oil F2. c.…

Q: absolute roughness is 0.03mm (for both sections), Determine the height H. Neglect local losses. Tip:…

Q: Q4) Water flows through a contraction section as shown. A pressure gage connected between the…

A: Figure is as shown

Q: From section 1 at p₁-750 kPa, water flows through a galvanized iron pipe of 50 mm inside diameter…

A: Given, P1 = 750 kPa D = 50 mm L = 40 m Q = 0.015 m3/s

Q: 36 " chinge Linseed Oil А (SG = 0.938) Castor Oil 32 feet (SG = 0.96) 7 feet 11ater В

Q: Q2. Two concentric glass tubes immersed in water as shown in figure. The outer square tube has edge…

A: Capillary tubes are thin cylindrical tubes with extremely tiny diameters. The liquid in the…

Q: where r, is the pipe radius. Calculate the shear stress (a) at the centerline, (b) at r = 0.25 cm,…

Q: A water pipe gradually changes from 150 mm at a point X to 450 mm at point Y. Point X is 5 m below…

Q: Water is pumped through a vertical steel pipe to an elevated tank. D = 10 cm, P₁= 1.6 MPa, L = 80 m,…

A: Given data:- The given diameter, D=10 cm=0.1 m The given Pressure at 1, P1=1.6 MPa The given Length,…

Q: :-For the horizontal water pipe shown , find the change in diameter if the far and of pipe is : a)…

A: given data h= 85m we have to determine the change in diameter

Q: Problem Water is pumped through a vertical steel pipe to an elevated tank. D = 10 cm, P₁= 1.6 MPa, L…

A: Given data:- Diameter of pipe, D=10 cm Length of the pipe, L=80 m Pressure, P1=1.6 MPa=1.6×106 N/m2…

Q: /For the horizontal water pipe shown, find the change in diameter if the far and of pipe is: a)…

A: Given D=300 mm t=8mm E= 200 GPa

Q: 2) Assuming uniform velocity profiles, find the force F needed to hold the plug in the pipe shown in…

Q: Based on the layout of the water supply system, as show in Figure 1, flow through the delivery pipe,…

A: Given, Q = 2.5 cfs D = 2.65 in or 0.2208 ft

Q: A) Water at 70 °C flows up a 50-ft-long conical pipe with its centerline sloping at 5° to the…

Q: Water flows through the pipe contraction as shown in the figure. The drop in the piezometer level…

A: According to given data Water flows through the pipe contraction The drop in the piezometer level…

Q: Water flows through a pipe at 15 L/s as shown. If the gage pressure of 12.5 kPa, 11.5 kPa and 10.3…

A: The values and figure given in the question are as follows: Discharge through pipe(Q)=15 L/sec…

Q: For a vertical rectangular gate, one side has linseed oil (0.938) and the other has two…

Q: A water siphon having a constant inside diameter D of 4 in. is arranged as shown in the figure…

A: ###Determination of Discharge through siphon ####

Q: In the figure, friction loss between A and B is neglected while between B and C it is 0.2 (VB²/2g).…

A: Given, In figure, The diameter of pipes A&C = 443mm =0.443m Diameter of pipe B= 131mm= 0.131m…

Q: For the conditions shown in schematic 1m figure, find the force F required to lift the Absolute…

Q: Calculate the total hydrostatic force and the location of the center of pressure (y,) acting on the…

Q: (Bernoulli/continuity) Water flows steadily through the pipe shown in the figure below such that the…

A: Assuming, Water is incompressible and steady. Given data, P1 = 262kPa P2 = 116 kPa D1 = 0.11 m V1…

Q: Bernoulli/continuity) Water flows steadily through the pipe shown in the figure below such that the…

Q: 4) Water flows through a contraction section as shown. A pressure gage connected between the…

Q: H.W. I The velocity distribution for flow over a plate is given by c= 3 d - 2 d where c is the…

Q: A pipe carrying water tapers from a diameter of 600 mm at 'A' to a diameter of 200 mm at 'B'. At 'A'…

Q: Example 4-6: The water flows through the pipe bend with a discharge of 200LS. The bend is placed…

A: Answer We can determine the the Magnitude and Direction of the resultant force(R) on the bend by…

Q: 1. Situation I. A 3 m square plate is immersed vertically in water such that the two edges of the…

Q: The 5m radius cylindrical gate shown is 8m long into the paper. If 0 = 60°, determine the location…

Concept explainers

Friction

Friction is defined as the force that prevents any solid surface, any layer of fluid, or any kind of element or material from sliding.

Question

A shunt pipe placed horizontally is shown on the right. The average
velocity of section 1 is
V1 = 3.5 m/s and its water pressure is P1 = 140 kPa. Does not
consider energy loss
If it is lost, try to find the magnitude and direction of the external force
required to fix the shunt.

21
D₁
D₁ = 0.15 m
1
1/201
D2
P2
D₂ = 0.076 m
60°
x
60°
D3 D3 = 0.1 m
P3
½/201

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Given data

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Water at 60 degrees Fahrenheit have a density of 62.36 Ib/ft.^3 and dynamic viscosity of 7.536 x 10^-4 Ib/ft-s) is flowing steadily in a 2-inch diameter horizontal pipe made of stainless steel at a rate of 0.2 ft^3/s. Use f = 0.0200. Determine %3D the head loss in terms of inches over a 200-feet long section of the pipe. A) 327.60 В 27.30 C 376.05 D None of the above
The canal shown below runs 40 m into the paper. Assume unit weight of H2O is 9.79 kN/ m^3. Compute the location of the center of pressure where the resultant strikes the wall measured Vertically and horizontally from the bottom of the quarter circle wall. 18m 40 18m 18 Unit of the Correct Answer: meter Decimal Places required in the final answer: n/a X = 7.639, Y = 6 X = 2.816, Y = 9.667 X = 6, Y = 7.639 X = 9.667, Y = 2.816
The flow rate of water flowing out of an 80mm diameter nozzle shown in Figure 1 is 60 litre/s. The volume of the water in the pipe bend is 50 litres and the pipe bend is installed in a vertical plane. The head loss from point 1 to 2 is 0.44m. Calculate the x and y for components of the thrust block to hold the pipe bend. Horizontal Thrust block 30° 50° Open end Ø80 mm Ø 160 mm Figure 3 Cs Scanned with CamScanner Vertical
Answer must correct. Fast Don't hold the Question
answer number 2.show your solution asap
e7
PROBLEM 3: For a vertical rectangular gate, one side has linseed oil (0.938) and the other has two fluids-castor oil (0.96) and water. Considering a unit-width of the gate, apply the PRESSURE PRISM CONCEPT (1llustrate and label the pressure diagram/prism) to calculate the magnitude and direction of the following when z = 7m. 1m hinge Linseed Oil (SG = 0.938) Castor Oil (SG = 0.96) 10 m 2 m water The hydrostatic force due to linseed oil F1.
mater 7
Handwritten pls.
Water flows through a pipe at 152 L/s that changes gradually in diameter from 196 mm at point A to 456 mm at point B. Point B is 6 m higher than point A. The pressures at point A and point B are 126 kPa and 69.3 kPa, respectively. Assume that the datum line passes through point A. Which of the following most nearly gives the head loss in the pipe? (m). Round your answers in 3 decimal places.
Note:hand written solution should be avoided.