Three concrete pipes are connected in series as shown. If the rate of flow in the pipe is 0.53 m3/s. Length for pipe 1 = 442 m Length for pipe 2 = 438 m Length for pipe 2 = 895 m   Diameter for pipe 1 = 279 mm Diameter for pipe 2 = 401 mm Diameter for pipe 3 = 318 mm   f for pipe 1 = 0.0446 f for pipe 2 = 0.0344 f for pipe 3 = 0.05   Determine the total head loss of the pipe in meter.    Round your answer to 3 decimal places

Q: Hi please could you jelp with this question and explain the method next to calcs? In the picture…

A: To solve this question, first we will calculate the area of the pier. Then we will find the value of…

Q: Problem 2: The steel shaft below is part of a mechanical assembly. The shaft is rotating at 125…

A: The rotation of the shaft at target rotation per minute results in the generation of power.  The…

Q: For the hydraulic system shown below. 1- Determine the resistance and discharge of each pipe. CLO1,…

A: Given, PA=100 KPa Head=PA9.81=10.19 m Net head =10.19+40=50.19 m Let head loss in pipe 1 =△h1 Head…

Q: Stoke's Viscosity - GLYCERIN Temperature = 17 C Fluid: Sp. Gravity of fluid G = Compute density of…

A: Hi there!! since you have asked multiple questions, we will solve the first question for you. If you…

Q: Solve for the water discharges in cach steel pipe as shown in Figure 3. You may assume that the…

A:

Q: Given the following information about a length of pipe: P1 = 440 kPa V1 = 0.0085 m/s z1 = 5 m v2 =…

A: Applying Bernoulli`s equation between point 1 and 2 in the given pipe flow:…

Q: From section 1 at p₁-750 kPa, water flows through a galvanized iron pipe of 50 mm inside diameter…

A: Given, P1 = 750 kPa  D = 50 mm L = 40 m  Q = 0.015 m3/s

Q: Water (density = 1.94 slugs/ft³; kinematic viscosity = 0.000011 ft²/s), is pumped between two…

A: Solution: Apply the Bernoulli equation between points 1 and 2 located at the water surface elevation…

Q: Water flows through a horizontal bend in the (x, y)-plane and discharges into the atmosphere as a…

A:

Q: Consider a constricting portion of a pipeline carrying water vertically downward as pictured. At the…

A: Given:-  Diameter at point 1 (d1) = 7 inches  Velocity at point 1 (V1) = 10 ft/s  Height of point 2…

Q: Q1) Water flows through the sudden pipe expansion shown below at a flow rate of 3 m3/s. the small…

A: There will be minor energy losses in the pipe flow system due to the sudden expansion of the pipe.…

Q: Q1, ( through a filter and then is circulated back to the tanks as shown below. The flowrate is 0.08…

A: Given, Q = 0.08 cfs v = 1.21 x 10-5 ft2/s

Q: Compute the Reynolds number for the flow of 895 L/min of water at 10°C in a standard hydraulic steel…

A: Q1 = 895l/min  Q2 = 46l/min

Q: The four pipes below have steady flow of an incompressible, ideal fluid with density ps. The…

A: Four manometers are given with the three pairs of options

Q: Hollow shaft AB (4" outside diameter, 3.5" inside diameter) is made of aluminum (E=10x106 psi,…

A:

Q: From the figure shown which of the following gives the best outside diameter in increments of 2mm. D…

A: Given: D = 875 kN L = 1450 kN Fy = 290 MPa Thickness of the pipe, t = 12 mm Length of the column. L…

Q: Your assigned problem: If the water surface elevation in reservoir B is 110m, what must be the water…

A: From the given question it is required to calculate the surface water elevation in reservoir A.

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?