A pipe carrying water tapers from a diameter of 600 mm at 'A' to a diameter of 200 mm at 'B'. At 'A' the mean velocity is 0.6 m/s and the gauge pressure is 450 kPa. Assuming friction effects are negligible, determine the pressure at 'B' which is 10.0 m above 'A'. $600mm B 10m Ø200mm

A pipe carrying water tapers from a diameter of 600 mm at 'A' to a diameter of 200 mm at 'B'. At 'A' the mean velocity is 0.6 m/s and the gauge pressure is 450 kPa. Assuming friction effects are negligible, determine the pressure at 'B' which is 10.0 m above 'A'. $600mm B 10m Ø200mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water flows from a to e through the pipe system shown in the figure. It is known that the flow in pipe bfgc is 50 liters per sec. (a) Assuming that C1 = 120 for all the pipes, determine the total flow from a to e. (b) Assuming that all the pipes are level and that the pressure head at a is 80 m, determine the pressure head at point d.
13
Show your solutions.
Problem 2: Comparing Three Equations for Head Loss Compare three equations for friction head loss in pipes, assuming constant friction factors. Recall the slope of the energy grade line (EGL) is S = he/L. Part A i. Write the Darcy-Weisbach equation for friction head loss, ht=... ii. For iron pipes, what is a typical, midrange value for the friction coefficient, λ? iii. For constant 2, if the discharge is doubled, by what factor does the head loss increase? Part B i. Write the Hazen-Williams equation for friction head loss, ht=... ii. For iron pipes, what is a typical, midrange value for the friction coefficient, CHW? iii. For constant Chw, if the discharge is doubled, by what factor does the head loss increase? Part C i. Write the Manning equation for friction head loss, ht=... ii. For iron pipes, what is a typical, midrange value for Manning's n, with units? iii. For constant n, if the discharge is doubled, by what factor does the head loss increase?
Oil (SG oil = 0.95) flows at 200 L/s through a 200mm diameter pipe, 500m long. Friction factor is 0.0225. Determine a) the head loss and b) the pressure difference between the endpoints of the pipe if the pipe slopes down at 10 degrees from the horizontal in the direction of flow (starting point is higher than the end point). A) hf = 132.19m B) No answer among the choices in question B No answer among the choices in question A (D) P1-P2 = 247.11 KPa E hf = 116.16m (F) P1-P2 = 288.22 KPa G) hf = 158.91m (H) hf = 186.46m P1-P2 = 260.17 KPa JP1-P2 = 273.81 KPa
kindly answer letters e, f, g, and h only
Read the question carefully and give me right solution
PROBLEM 3: For a vertical rectangular gate, one side has linseed oil (0.938) and the other has two fluids-castor oil (0.96) and water. Considering a unit-width of the gate, apply the PRESSURE PRISM CONCEPT (1llustrate and label the pressure diagram/prism) to calculate the magnitude and direction of the following when z = 7m. 1m hinge Linseed Oil (SG = 0.938) Castor Oil (SG = 0.96) 10 m 2 m water The hydrostatic force due to linseed oil F1.
Water flows through a pipe at 152 L/s that changes gradually in diameter from 196 mm at point A to 456 mm at point B. Point B is 6 m higher than point A. The pressures at point A and point B are 126 kPa and 69.3 kPa, respectively. Assume that the datum line passes through point A. Which of the following most nearly gives the head loss in the pipe? (m). Round your answers in 3 decimal places.
Please solve Thank you
Handliston A steel penstock 500 mm in diameter has shell thickness of 10 mm. The modulus of elasticity of the shell material is 2.0 x 105 N/mm2 & the bulk modulus of elasticity of water is 2.0 x 103 N/mm2. The pipe is designed to discharge water at a mean velocity of 2.0 m/sec. Determine the pressure rise caused by the sudden closure of a valve at the downstream end by neglecting the elasticity of the pipe material.
Q- In a pond at a depth of 5m air bubble is formed of diameter 0.8mm. Calculate gauge pressure inside air bubble. Assume surface tension = 0.075N/m.