B- in figure below the plat has a width of 1 m. the heater is connected to the heater has length of 50mm what is the maximum heater power required?. Air T-25°C = 60 m/s con T_= 25°C = 60 m/s -Plate 1 Plate 1 7₁-230°C Plate 5 -T₁ = 230°C www -150 mm -- Quixx = 50 mm L=250 mm 2- Typical heater Insulation IL₁

B- in figure below the plat has a width of 1 m. the heater is connected to the heater has length of 50mm what is the maximum heater power required?. Air T-25°C = 60 m/s con T_= 25°C = 60 m/s -Plate 1 Plate 1 7₁-230°C Plate 5 -T₁ = 230°C www -150 mm -- Quixx = 50 mm L=250 mm 2- Typical heater Insulation IL₁

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter28: Special Refrigeration Applications

Section: Chapter Questions

Problem 4RQ

See similar textbooks

Similar questions

Please dont late give me Last number
i need the answer quickly
I need answer in handwritten
could you help me with this problem
Please find the highest thermal efficiency possible, while remaining within the boundaries. What is required: -Power produced must be at least 60 Mega Watts -Thermal efficiency must be greater than 36% -Back-work ratio must be smaller than 48% Assume: -air is the working fluid -specific heats vary with temperature (use table A-17) -Compressor inlet is at 1atm and 300k -the combustion process is isobaric and is modeled as a heat exchanger -Turbine exhaust is the same pressure as compressor inlet Compressor specifics: -Max volume flow rate (m^3/h) = 600,000 -Max outlet pressure (atm) = 12 -Isentropic efficiency = 90% Combustion chamber and gas tubine specifics (Note these come as a set) -Max pressure = 16.7 atm -Max temp = 1500 (celcius) -Turbine isentropic efficiency = 92% -Max heat rate = 230MW
its an answer please typ it i cant read it
solve using image, please don not resend other solutions previosly posted in bartebly ,as the are wrong thanks
Hi, can you only help with A and B here? I am looking to get this started. Please draw a clear schematic if you think it differs from the picture in any respect.
NOTE: Only answer the highlighted parts, because a-c has already been answered, only answer letters G H and I. ThanksAn Ammonia refrigerant vapor compression system is utilized as an air-cooled water chiller. It is operating at a condenser temperature of 40oC and an evaporator temperature of 0oC. The system develops 15 Tons of Refrigeration. Determine:g. LMTD and AMTD in the condenserh. The water flow rate of the chiller if it enters the evaporator at 10oC and leaves at 5oC.i. LMTD and AMTD in the evaporator
i need the answer quickly
Please help me solve D, E, F, Only
Determine a. the heat requirement b. the size of the settling/coalescing section of a horizontal heater treater for the following conditions: Oil flow rate= 5,000 BOPD Inlet oil temperature Water SG Inlet BS&W Outlet BS&W Retention time = 80°F = 1.04 = 10% = 1% = 20 mins Investigate treating at 80°F, 100°F, 120°F. D-0 21