If the suction pressure is 1 point decreased * the refrigerating effect is going to decrease and the work required for compressor is going toincrease Nothing would happen the heat rejection in the condenser would increase the refrigeration capacity will increase

Q: How does Impulsive forces occur?

A: Impulsive force:- When a force acted on a body for short period of time then it is called impulsive…

Q: n's Law of Motion odynamics mples (situational or not) from e

A: To give: The summary of Newton's Laws of Motion and Thermodynamics, with some examples.

Q: Define the term form factor?

A: Generally, the word Form factor is defined for the surface finish and tolerance provided over any…

Q: t is the figure called? explain and elaborate

A: The apparatus is a open cup flash point test apparatus

Q: would it be possible to get a detailed explanation? thank you

A:

Q: For the process shown in the schematic below, which of the statements is/are incorrect? Feed hopper…

A: 1)b. The process can only work with thermoplastics and not with thermosets due to the thermal…

Q: 1- A simple introduction. 2- The benefits of this process. 3- The disadvantages of this process. 4-…

A: The mechanical motion of a punch is used to deep draw sheet metal. Under consistent hydrostatic…

Q: can I have FBD for this?

A:

Q: Which of the following is NOT TRUE with respect to the Elastic Transverse Shear Formula?…

A:

Q: If a car weighing 2400 lbs is able to go 1000 ft up a mountain incline whose angle of inclination is…

A: Given data: Weight of car = 2400 lbs                      Distance which car moves up the incline =…

Q: Stanum is vital as mankind enters Stone age New age Brass age Bronze age

A: Correct answer: Bronze age

Q: Hi, please complete the last three subparts of this question.

A: To calculate the rate of heat transfer, to derive and to calculate the mass flow rate of water, flow…

Q: Water flows from a large tank into a 6" diameter pipe through an entrance condition of a square…

A: Given:Pipe diameter, D2=6 inchRadius of the rounded inlet, r=0.12 inchFind:The head loss reduced at…

Q: Name the views that are used to show the part.

A: Engineering drawing is an arrangement of different drawings of a single object viewed from the…

Q: Is this the only correct option in the question above? I think the question is worded for more than…

A: To elaborate why a sling psychrometer can measure humidity.

Q: Which is the "noise"?

A: We can produce sound by creating some vibration with objects.

Q: Figure A. Rectangular block of steel. Adapted from: https://media.wdscomponents.com/ri-…

A: Given: Workpiece is slimmed using slab milling To find: 4 items need to perform slab milling process

Q: Define 'power'.

A: It can simply defined as the amount of work done per unit time. Or the rate of time of doing work or…

Q: The beam has a rectangular cross section and is subjected to the loading shown. Determine the state…

A:

Q: What's the worst car ever made?

A: Given Data⇒ worst car Problem statement⇒ Problem says What's the worst car ever made?

Q: Describe the work done is proportional to the force applied (F ) and the distance traveled (s).

A: We know that,Work Done =Force × DisplacementW = F × s From the above equation, If…

Q: Distinguish between the Surface Loads and the Distributed Loads?

A: Load is defined as an external force or a couple to which a member is subjected during its…

Q: So what are the correct answers

A: Explanation: If we consider a system that loses heat δQ at temperature T. Since, In this case the…

Q: Using scientific methods, how would you know the right temperature and heat needed to bake to right…

A: Following steps can be used - With the help of protein denaturation temperature, we can know the…

Q: Explain three pages of laminar flow with the drawing

A:

Q: trenching  machine design and modeling.  Each concept must have an introduction and design…

A: Equipment that is portable and built for small-scale trenching operations is the tiny excavator…

Q: The following data are available from orthogonal cutting experimental. In this case: Thermal…

A: Solution:

Q: ACCURATELY

A: We have given ACCURATELY

Q: horwalizing 1) Machinability of low carbon steels improved by: high carbon steel improved by…

A: Heat treatment processes are used to get the desired properties in the metals.

Q: Manufacuring Processes An electro chemical machining (ECM) operation is employed too cut a square…

A: Write the given data:

Q: Q2: Select any one casted component shown in the figure which is made up of alloy material and used…

A: I will select second one i.e  spiral bevel gear. Alloys used in making gears is zinc alloys  or…

Q: have you figured out part b yet?

A: To determine the magnitude of the reaction force at each bearing, we'll relate the acceleration of…

Q: a BUE? Why does it form?

A:

Q: c. In the field, the position of the interface between oil and water is often difficult to determine…

A:

Q: 6. Low carbon steel can be machined using Abrasive jet machining. 7. Tool life in EDM is infinite.…

A: Note: Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: part ii

A: