Determine a. the heat requirement b. the size of the settling/coalescing section of a horizontal heater treater for the following conditions: Oil flow rate= 5,000 BOPD . Inlet oil temperature Water SG Inlet BS&W Outlet BS&W Retention time = 80°F = 1.04 = 10% = 1% = 20 mins Investigate treating at 80°F, 100°F, 120°F.

Determine a. the heat requirement b. the size of the settling/coalescing section of a horizontal heater treater for the following conditions: Oil flow rate= 5,000 BOPD . Inlet oil temperature Water SG Inlet BS&W Outlet BS&W Retention time = 80°F = 1.04 = 10% = 1% = 20 mins Investigate treating at 80°F, 100°F, 120°F.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

solve using image, please don not resend other solutions previosly posted in bartebly ,as the are wrong thanks
Question 2 A 1-1 shell & tube exchange is with Sulfuric Acid flowing at 115 gpm, at 80.33 F (Cp=.02 Btu/lbm-F) (SG=1.8), to cool 70 gpm of water from 175 F to 100 F in a counter-current mode. A) Assign shell side fluid. Explain your decision. B) What is the total hot side heat duty? C) Calculate LMTD D) What is the value of Ft and what does it mean? E) Assume a "typical heat transfer coefficient" conservatively, estimate the exchanger area in Ft²?
Show complete solution and illustration please.
Mechanical EngineeringThermodynamicsTopic: Rankine Cycles
A power plant was analysed based on Carnot cycle, the evaporator supplie 442 kJ of heat per cycle at 512°C and condenser cooling fluid was maintained at 36°C. (a).Determine the amount of heat rejected in the condenser? Provide answer to no decimal place and insert the unit symbol in kilo.... 1 °C is 273K in this question if required.
no typing please handwright
11 MWth plant operates at a thermal efficiency of 34%. The waste heat is dumped across a condenser which operates at a shell side pressure of 0.717 psia. For the given information below, determine the condenser tube length. A Coolant Flow Rate 4.81 x 108 Ibm/hr Coolant Inlet Temperature 60 F Number of Tubes 62,832 Lattice triangular Pitch 1.5 inch Tube OD 1 inch Tube ID 0.944 inch Tube Thermal Conductivity 10 Btu/hr-ft-F Condensing Heat Transfer Coefficient 1228 Btu/hr-ft²-F
ENERGY PLANTS: Given : Turbine entry conditions = 16 MPa and 600 oC(Degrees Celsius) Turbine output=5 MPa Phase state saturated water at the heat exchanger outlet and heat exchanger efficiency 85% Required power for district heating = 1100 kW Turbine power= 5500 kW Question: What is the mass flow rate in the boiler?
Do not copy previous answer.. I want typing format answers. Please don't use handwritten answer.
• A 6 MW generator had a thrust of 103,000 lb. The outside diameter of the step bearing is 12 in, and the inside diameter is 8 in. Employ a film thickness of 0.004 in. Use SAE 20 oil at 120 , the specific heat of the oil being 0.6 BTU/lb deg F, and density of 0.307 lb/cu. in Determine: (d) Temperature rise
Please dont late give me Last number
Refrigerant 12 Condensing temperature = 46.2 oCEvaporating temperature = -3 oCTemperature of the suction vapor = -15.6oCRefrigerating Capacity for evaporator = 44 TONDetermine the COP