(b) A balanced Y-connected load has phase voltage of 230 V and positive phase sequence. The impedances Z4, ZB, and Zc are 10230° N, respectively. (i) By taking VAB on the load side as a reference, determine all the line currents and phase voltages. (ii) Determine total real power, P, total reactive power, Q and total apparent power, S of the system. (iii) Total real power of the loads can be measured using two wattmeter methods. Draw the connection of the two wattumeters if their current coils are in line A and C, respectively. What is the total real power measured by each wattmeter? Prove and compare the value with Q2(b)(ii). I

(b) A balanced Y-connected load has phase voltage of 230 V and positive phase sequence. The impedances Z4, ZB, and Zc are 10230° N, respectively. (i) By taking VAB on the load side as a reference, determine all the line currents and phase voltages. (ii) Determine total real power, P, total reactive power, Q and total apparent power, S of the system. (iii) Total real power of the loads can be measured using two wattmeter methods. Draw the connection of the two wattumeters if their current coils are in line A and C, respectively. What is the total real power measured by each wattmeter? Prove and compare the value with Q2(b)(ii). I

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

This question in (three phase) subject.. I want the the correct answer from choices ..
consider the following diagram of impedances in per unit of a common base a) get the YBUS admittance array and the ZBuz impedance array 213-j2 pu zt2-j0.15 zg2-j1.85 791-j0.9 211-0.1 1 212-j0.5pu 223-j0.5pu Va 1 p.u. Jv1-1p.u. 22-10 pu
In a single phase equivalent circuit, the current in the a-phase conductor line is simply the voltage generated in the a-phase winding of the generator divided by the total impedance in the a-phase of the circuit. Select one: O True O False
Draw a 3-phase wye-connected generator with transmission lines connected to a 3-phase delta-connected load. Assume the lines connecting them have an inductance of j5 per phase. The generated voltages are 120 Vrms with phase 'a' having a phase angle of 0°. The loads are 10 Ohm resistors per phase. When drawing, make sure to label all 3 phases with voltage phasors, line inductances, and load resistances.
Referring to the circuit shown in Figure 1 below, solve the following problems: - i) Calculate the total impedance, ZT. ii) Determine the total current, Ir supplied by the generator iii) Determine the value of current at load impedance, I1, I2 and I3. iv) Calculate total real power, PT and reactive power, Qr supplied by the generator. v) Draw a power triangle of this circuit vi) Calculate the power factor of this circuit.
Phase Qz/ The eas Voltages at the terminal of abalan ced Y connected load is VAN=12o 28. Each Phase of the load consist of lo 230° .Find the active & Reactive and Complex Power Per-Phase then find the total Powers For three Phase load.
Suppose you have a three-phase generator that provides 120 Vac per phase and works at a frequency of 60 Hz, this generator can be connected in both delta and star. Also consider the following 6 load impedances, which will be connected at the same time to the generator as follows: ZA, ZB and Zc are connected in star, while Zp, Zg and Zp are connected in delta. j20 j3n Za j20 ZA j30 j3n -j20 j 30 -j20 Zo -j20 ZE j30 -j2n j 3n. ZF Assume the generator is star-connected with neutral, calculate total system power, total power factor, and current in neutral.
In the figure, bus 1 is the reference bus, V1 = 1.06 p.u and the angle is 0.. A load with active power= 100 MW and reactive power = 50 Mvar is connected to bus 2. The line impedance is z12 = 0.12 + j0.16 p.u on a base of 100 MVA. Start with an initial estimate of |V2|0) = 1.0 p.u and 820) = 0•. Find |V2| () (one iteration). 100 MW 212 = 0.12 + j0.16 ++ 50 Mvar Vị = 1.0/0° О а. |V2| (1) = 0.4 p.u. Ob. |V2| (1) = 0.5 p.u. Oc. |V2| (1) = 0.7 p.u. d. (1) = 0.8 p.u. е. |V2| (1) = 0.6 p.u.
I need the answer quickly
What is the max load demand of the following feeders 4152 MW, 2.891 MW, 815.20 KW, 905.12 KWand 1.972 MW A) 10,735.32 KW B) 12,815.32 KW C) 10,571 MW D) 12.052 MW
Solve A-E
A circular coil of 100 turns with a cross- - sectional area of 1 m² is kept with its plane perpendicular to the magnetic field of 1 T. The magnetic flux linkage is