Three Impedances each of (8 - j18) are connected in mesh across a three-phase 410V ac supply. Determine the phase current, line current, active power, reactive power drawn from supply. Also draw the Phasor diagram for the mesh connection and marks the Line current ,phase current line voltage and phase angle between phase current and pahse voltage. I phase current (Ip) Line current real power reactive power

Three Impedances each of (8 - j18) are connected in mesh across a three-phase 410V ac supply. Determine the phase current, line current, active power, reactive power drawn from supply. Also draw the Phasor diagram for the mesh connection and marks the Line current ,phase current line voltage and phase angle between phase current and pahse voltage. I phase current (Ip) Line current real power reactive power

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

"As per the standards used in power system, even harmonics are limited to 25 percent of the odd harmonic limits" True False
A three-phase balanced load of 15A per phase is supplied by a steel wire armoured cable with a c.s.a. of 2.5mm². The voltage drop for this cable is 15mv/A/m and the circuit is 40m long. Calculate the voltage drop in the cable.
Subject - Design electrical circuits for single phase AC networks Question - Analyse the methods that improve the power factor of a electrical circuit.
A source of AC emf E₁ = 120/300 volts with an impedance of Z₁ = 2/0° ohms is connected in parallel with another AC source of E₂ = 120/-30º volts with an impedance Z₂ = 2/90° ohms. The two AC source are use to supply a load impedance of Z₁ = 10/-53.10 ohms. Calculate the value of the load current IL. O a. 7.62 amperes O b. 4.42 amperes O C. 5.38 amperes O d. 6.48 amperes
Q5/C: Compare between Auto transformers and 2 winding transformers.
From the circuit below, determine secondary winding voltage Vsec if the primary winding voltage Vpri = 120Vrms? Np:Ns 6:1 Vp 120 Vac 60 Hz out R = 200 ) O Ovrms O 720Vrms 120Vrms O 20Vrms wi m
Design a CT-FWR to supply a load of (502) with a waveform of the following specifications: - • Vdc = 12 V • Ripple factor = 0.1 % • the main power supply is (220 Vrms, 50 Hz). Determine the following values: - 1- The value of capacitor filter. 2- The maximum load voltage (VmR) 3- The transformer turns ratio (a). 4- The RMS value of the load voltage. 5- Draw the output waveform. (assume ideal diodes)
For the same alternator the ratio of rated kva, when connected as a three phase winding alternator to when connected as a single phase alternator by using all the coils is
Subject - Design electrical circuits for single phase AC networks Question - Compare the effect of varying resistance, capacitance and inductance in a pararllel and series AC circuits on voltage resistance and impedance.
In Fixed-bias configuration, the DC voltage across the Source terminal is equal to ____. a.Vgs b.0V c.Vp d.Vds
What are the applications of IMPEDANCE and ADMITTANCE OF AN AC CIRCUIT
From the circuit below, determine secondary winding voltage Vsec if the primary winding voltage Vpri = 120Vrms? %3D Np:Ns 6:1 D. Vp 120 Vac 60 Hz Vout R = 200 Q O 20Vrms O 720Vrms O 120Vrms O Ovrms wi m