Q4: Design a buck-boost converterto provide an output voltage 12V from a source that varies 'between 10V-16V.Given the load resistor is 10 ohm. assuming the frequency is 50 KHzand the output voltage ripple is 1.5% Specity:a. The duty ratio.b. The value of inductor.c. The value of capacitor.Note: Determine the values of inductor and capacitor with D1 only.

There are three types of DC/DC converter is used in power electronics. They are Buck converter: In…

Answered: Q4: Design a buck-boost converter to…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Vin = 10 mV Sin (wt) HH inf 1. For the Diode Circuits shown below, Vd-0.7v a. Draw the small signal eq. circuit find Vo (AC+DC) b. C. Sketch the output waveform Vo (AC+DC) V1 vin D Find the cascaded voltage gain Yout/Vin of the follo I'C 5 R2 25 11 1m D1 dio R1 300 Vo
An unipolar PWM full bridge circuit has a Vr.rms of 125V at a duty cycle D1 of 0.7. What is Vd? What is Vo.rms?
The input voltage (vin) of the following circuit is a sinusoidal signal with an amplitude of 2Vrms,consider a silicon diode.graph the output voltage ?? and the current across the resistor.
4. A biased clamper is connected to a rectangular AC input with 20V on the positive half cycle and -10V on the negative half cycle. The orientation of the Si diode is the same with Vo while the 5V biasing voltage is in opposite connection. The value of R is 100K ohms while the capacitor is 1 microFarad. Find the voltage across the capacitor. Estimate the amount of time needed to fully discharge the capacitor. Find the magnitude of the output swing. Find the output voltage (Vo) during the negative half cycle. Find the output voltage (Vo) during the positive half cycle. Find the value of the Time Constant (Tau).
A step down converter is operated with a duty cycle of k = 0.75. The input voltage is Vs = 20V, and the load is: L = 5mH, R = 1502. The minimum inductor current is I₁ = 0.1A. The maximum inductor current is: Select one: a. 1.9 A b. None of these OC. 0.9 A O d. 1.1 A Oe. 2 A
Kindly solve all the parts for me
p3. A biased parallel clipper is connected to a squarewave 20VAC input.The biasing voltage of 5V has the same polarity with the Vo while the Si diode is connected in reverse and will conduct only during negative half cycle. In P3, what is the output voltage (Vo) during the positive half cycle? a. -4.3V b. 20V c. 4.3V d. -12.15V
INCLUDE ALL THE DECIMALS.
C'uk Converter Design A C'uk converter has an input of 12 V and is to have an output of - 24 V supplying a 60 W load. Select the duty ratio, the switching frequency, the inductor sizes such that the change in inductor currents is no more than 12 percent of the average inductor current, the output ripple voltage is no more than 1.5 percent, and the ripple voltage across C1 is no more than 3 percent.
The circuit below has a variable voltage vin as its input. We are interested in Vout as a function of Vin. In other words, if we vary the value of the voltage source vin, what will be the effect on the voltage Vout? The steps below will help you to investigate this question, and your answers will form the basis for a new design. Assume that the diode can be sufficiently modelled as simple diode with forward voltage of 0.7 V (you do not need Shockley's equation). Vin 100Ω M Vf = 0.7 V 2 V V out

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS