B – 3 ft - 6 ft 3 ft- 2 in. 6 in. 1 in. 2 in. 1 in.

Q: P

A:

Q: The rigid beam is supported at its ends by two A-36 steel tie rods. The rods have diameters dAB =…

A: Draw the free-body diagram of the beam.

Q: The tension member is fastened together using two bolts, one on each side of the member as shown.…

A: Given data: Diameter of bolt, d = 0.3 in. Shear stress, τ = 12 ksi Normal stress, σ= 20 ksi The free…

Q: If the intensity of the load w = 15 kN>m, determine the absolute maximum tensile and compressive…

A: Given data: Load intensity, W = 15 kN Draw the free body diagram of the beam.

Q: If the allowable normal stress for the bar is s allow = 120 MPa, determine the maximum axial force P…

A: Write the given data:

Q: The screw of the clamp exerts a compressive force of 500 lb on the wood blocks. Determine the…

A: Area at section (a-a) Moment of inertia at section (a-a)

Q: P a

A: GIVEN DATA- 23.5-mm-diameter pin at A P = 28.36 kN, a = 2.25 m, and b = 6.56 m.

Q: The hook is subjected to the force of 80 lb. Determine the state of stress at point B at section…

A: Given Diameter of the cross-section D=0.5 in. Force subjected on the hook F=80 lb.

Q: A purse hook is used to hang a handbag from the edge of a table with L = 50 mm. If the cross section…

A: Calculated normal stress at A, B and C and y position where normal stress equals zero

Q: The singular force F will be applied to the beam with a hollow rectangular cross section.…

A:

Q: The compound wooden beam is connected together by a bolt at B. Assuming that the connections at A,…

A: Given data: Permissible screw stress,σtper=150MPa Permissible bearing stress for wood, σbper=28MPa

Q: The beam is supported by a Pin at A and a short link BC. If P = 15 kN, determine the average shear…

A:

Q: Consider the wooden member subjected to a tensile load P = 11.00 kN. Determine the shear stress at…

A: Given data: ● The axial force on the wooden member: P = 11.00 kN = 11000 N ● The cross-sectional…

Q: Determine the shear stress at point B on the web of the cantilevered strut at section a–a.

A: Given Applied loads 2 kN and 4 kN To find Shear stress at point B

Q: If the allowable tensile stress for wires AB and AC is sallow = 200 MPa, determine the required…

A:

Q: If a = 3 in. and the wood has an allowable normal stress of sallow = 1.5 ksi, and an allowable shear…

A: The section modulus of the rectangular cross-section about the neutral axis is…

Q: Determine the maximum compressive stress in the bracket at section a-a when the load P = 70 kN is…

A: Given that ,  P=70kN at x=0

Q: The joint is subjected to the axial member force of 6 kips. Determine the average normal stress…

A:

Q: Figure. rod 2m. 2m. 60

A:

Q: Determine the maximum shear force V that the strut can support if the allowable shear stress for the…

A: Given data:  allowable shear stress (τallow) = 40 MPa =τmax Find, Maximum shear force (Vmax)

Q: If the load has a weight of 600 lb, determine the maximum normal stress on the cross section of the…

A: Given Data: Weight of the load is F = 600 lb. Distance between load and section is l = 1.5 ft.…

Q: The block is subjected to the eccentric load shown. Sketch the normal-stress distribution acting…

A: Given Applied load = 150 kN To find The normal stress distribution

Q: Determine the maximum compressive stress in the bracket at section a–a when the load P = 52 kN is…

A:

Q: Determine the principal stresses in the cantilevered beam at points A and B.

A: Draw sketch of beam and divide shear force into horizontal and vertical components.

Q: The plexiglass bar has a stress–strain curve that can be approximated by the straight-line segments…

A: From the given stress-strain curve for Plexiglas bar:  Failure point in Tension: σft=60 MPa and…

Q: The axial force in the column supporting the timber beam shown is P = 20 kips. Determine the…

A: Given data P=20 kipsσb=400 psi

Q: Please answer in this format: Given: Required: А. Од in kPa В. Ов in kPа С. Ос in kPa D. Op in kPa…

A:

Q: Q: The compound wooden beam is connected together by a bolt at B. Assuming that the connections at…

A:

Q: Determine the required diameter of the pins at A and B if the allowable shear stress for the…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.